DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
DTC P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0016 | Deviation in crankshaft position sensor signal and camshaft position sensor (for intake camshaft) signal (2 trip detection logic). |
|
| P0017 | Deviation in crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic). |
|
| Required Sensors/Components (Main) | Camshaft timing gear assembly Camshaft timing exhaust gear assembly |
| Required Sensors/Components (Related) | Camshaft position sensor Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Engine speed | 500 to 1000 rpm |
| Engine speed | 500 to 1000 rpm |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 AND P0017) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0016 or P0017 is output | A |
| DTC P0016 or P0017 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the A/C on.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 1) / All Data / VVT Change Angle #1, VVT Ex Chg Angle #1.
Perform the Active Test. Check that the displacement angle varies.
|
| ||||
| OK | |
| 3.ADJUST VALVE TIMING |
Adjust the valve timing (Click here).
|
| ||||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for intake or exhaust camshaft) (Click here).
|
| ||||
| OK | |
| 5.INSPECT OIL CONTROL VALVE FILTER |
Remove the oil control valve filter .
Check that the filter is not clogged.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Replace the camshaft timing gear assembly (for intake camshaft) or camshaft timing exhaust gear assembly .
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0017) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0016 or P0017 is output | B |
|
| ||||
| A | ||
| ||