AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn on the Intelligent tester.
Select the item "Enter / Powertrain / Engine and ECT / Data List".
According to the display on the tester, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP Switch Status/ON or OFF | Shift lever position is; P and N: ON Except P and N: OFF | When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Stop Light Switch | Stop Light Switch Status/ON or OFF |
| - |
| SPD (NT) | Input Turbine Speed/display: 50 r/min |
| - |
| SPD (NC) | Counter Gear Speed/display: 50 r/min |
| - |
| Shift SW Status (P Range) | PNP Switch Status/ON or OFF | Shift lever position is; P: ON Except P: OFF | When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Shift SW Status (R Range) | PNP Switch Status/ON or OFF | Shift lever position is; R: ON Except R: OFF | When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Shift SW Status (N Range) | PNP Switch Status/ON or OFF | Shift lever position is; N: ON Except N: OFF | When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Sports Shift Up SW | Sport Shift Up switch Status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport Shift Down switch Status/ ON or OFF |
| - |
| Sports Mode Selection SW | Sport Shift Up switch Status/ ON or OFF | Shift lever position is: S, "+" and "-": ON Except S, "+" and "-": OFF | - |
| Shift SW Status (D Range) | PNP Switch Status/ON or OFF | Shift lever position is; D and S: ON Except D and S: OFF | When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| A/T Oil Temperature 1 | ATF Temp. Sensor Value/min.: -40°C (-40°F), max.: 215°C (419°F) |
| If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor circuit is opened or shorted. |
| Lock Up | Lock Up Status/ON or OFF |
| - |
| Shift Status | Actual Gear Position/ 1st, 2nd, 3rd or 4th | Shift lever position is:
| - |
| SLT Solenoid Status | Shift Solenoid SLT Status/ON or OFF | Shift solenoid SLT is:
| - |
| DSL Solenoid Status | Shift Solenoid DSL Status/ON or OFF | Shift solenoid DSL is:
| - |
| AT Fluid | Flex lockup judder judgment flag / 0: OFF / 1: ON | - | - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn on the Intelligent tester.
Select the item "Enter / Powertrain / Engine and ECT / Active Test".
According to the display on tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)*
| [Test Details] Operate the shift solenoid SLT and raise the line pressure. [Vehicle Condition]
| ON / OFF | - |
| Activate the Solenoid (S4) | [Test Details] Operate the shift solenoid S4 [Vehicle Condition]
| ON / OFF | - |
| Activate the Lock Up | [Test Details] Control the shift solenoid DSL to set the automatic transaxle to the lock-up condition. [Vehicle Condition]
| ON / OFF | Possible to check the DSL operation. |
| Control the Shift Position | [Test Details] Operate the shift solenoid valve and set the each shift position by yourself. [Vehicle Condition]
| 1st / 2nd / 3rd / 4th | Possible to check the operation of the shift solenoid valves. |
| Activate the Solenoid (DSL) | [Test Details] Operate the shift solenoid DSL [Vehicle Condition]
| ON / OFF | - |
| Activate the Solenoid (SL1) | [Test Details] Operate the shift solenoid SL1 [Vehicle Condition]
| ON / OFF | - |
| Activate the Solenoid (SL2) | [Test Details] Operate the shift solenoid SL2 [Vehicle Condition]
| ON / OFF | - |