Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (RHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
  1. Short in CAN main bus line
  2. Short in CAN branch line
  3. ECM
  4. Main body ECU (Multiplex network body ECU)
  5. Combination meter assembly
  6. Brake actuator assembly
  7. Steering sensor
  8. Clearance warning ECU assembly
  9. Power steering ECU with motor assembly
  10. Airbag sensor assembly
  11. Air conditioning amplifier assembly
  12. Smart key ECU assembly (Certification ECU)*1
  13. Radio and display receiver assembly*2
  14. CAN No. 1 junction connector
  15. CAN No. 2 junction connector
*1: w/ Smart entry and start system
*2: for Radio and display type

WIRING DIAGRAM


C269154E01


C244451E02


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
  6. After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
  3. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

1.CHECK FOR SHORT IN CAN BUS LINES (DLC3 BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C250963E01
  1. Disconnect the DLC3 branch line connector (I96) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to DLC3

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3
OK


2.CHECK FOR SHORT IN CAN BUS LINES (BRANCH LINE)
  1. Reconnect the DLC3 branch line connector (I96) to the CAN No. 2 junction connector.



    C210421E47
  1. Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
    Text in Illustration 
    *1
    DLC3



  1. While observing the resistance value shown on the tester, disconnect connectors (I95, I102, I103, I100, I107, I106, I105, I97 and I111) from the CAN No. 1 junction connector or CAN No. 2 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

    HINT:
    Disconnect the branch line connectors other than those of the DLC3.


    C269155E01


    Text in Illustration 
    *A
    w/ Smart Entry and Start System
    *B
    for Radio and Display Type
    *1
    Clearance Warning ECU Assembly
    *2
    Steering Sensor
    *3
    Brake Actuator Assembly
    *4
    Smart Key ECU Assembly (Certification ECU)
    *5
    DLC3
    *6
    Combination Meter Assembly
    *7
    Radio and Display Receiver Assembly
    *8
    ECM
    *9
    Power Steering ECU with Motor Assembly
    *10
    Airbag Sensor Assembly
    *11
    Air Conditioning Amplifier Assembly
    *12
    Main Body ECU (Multiplex Network Body ECU)
    *13
    CAN No. 1 Junction Connector
    *14
    CAN No. 2 Junction Connector

    C250964E01


    Text in Illustration 
    *a
    Component without harness connected
    (CAN No. 1 Junction Connector)
    -
    -

    Wiring Color 
    CAN No. 1 Junction Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    Main body ECU (Multiplex network body ECU)
    I95
    P
    W
    Air conditioning amplifier assembly
    I102
    V
    W
    Airbag sensor assembly
    I103
    Y
    W
    Power steering ECU with motor assembly
    I100
    L
    W
    ECM
    I104
    G
    W
    Radio and display receiver assembly*1
    I107
    R
    W
    CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector)
    I93
    B
    W
    *1: for Radio and display type

    C269156E01


    Text in Illustration 
    *a
    Component without harness connected
    (CAN No. 2 Junction Connector)
    -
    -

    Wiring Color 
    CAN No. 2 Junction Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector)
    I101
    B
    W
    Combination meter assembly
    I94
    R
    W
    DLC3
    I96
    G
    W
    Smart key ECU assembly (Certification ECU)*1
    I106
    L
    W
    Brake actuator assembly
    I105
    Y
    W
    Steering sensor
    I97
    V
    W
    Clearance warning ECU assembly
    I111
    P
    W
    *1: w/ Smart entry and start system

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.


    Result:

    Symptom
    Proceed to
    The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.)
    A
    The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.)
    B

  1. When there is a short in one or more of the branch lines:

    1. Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

      HINT:
      1. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
      2. Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



B
Go to step 7
A


3.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)


    C250965E01
  1. Disconnect the combination meter assembly main bus line connector (I94) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to Combination Meter Assembly

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    Result:

    Symptom
    Proceed to
    The resistance is still below 54 Ω when the combination meter assembly connector is disconnected. (There are no shorts in the combination meter assembly or between its main bus lines.)
    A
    The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the combination meter assembly connector is disconnected. (There is a short in the combination meter assembly or between its main bus lines.)
    B



B
Go to step 8
A


4.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN LINE)


    C250966E01
  1. Disconnect the ECM main bus line connector (I104) from the CAN No. 1 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to ECM

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3

    HINT:
    Measure the resistance with the combination meter assembly main bus line connector (I94) disconnected.


    Result:

    Symptom
    Proceed to
    The resistance is still below 1 MΩ when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.)
    A
    The resistance becomes 1 MΩ or more when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.)
    B



B
Go to step 9
A


5.CHECK CAN NO. 2 JUNCTION CONNECTOR


    C250967E01
  1. Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to CAN No. 1 Junction Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPLACE CAN NO. 2 JUNCTION CONNECTOR
OK


6.CHECK CAN NO. 1 JUNCTION CONNECTOR
  1. Reconnect the CAN main bus line connector (I101) to the CAN No. 2 junction connector.



    C250968E01
  1. Disconnect the CAN main bus line connector (I93) from the CAN No. 1 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to CAN No. 2 Junction Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

Text in Illustration 
*1
DLC3


NG
REPAIR OR REPLACE CAN BUS MAIN LINES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)
OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR 

7.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
  1. Reconnect the connector for the short-circuited branch line to the CAN J/C (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).

  1. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the short-circuited branch line is connected (Click here).



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR 

8.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY)
  1. Reconnect the combination meter assembly main bus line connector (I94) to the CAN No. 2 junction connector.

  1. Disconnect the combination meter assembly connector.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.



NG
REPAIR OR REPLACE CAN BUS MAIN LINES (COMBINATION METER ASSEMBLY MAIN LINES)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

9.CHECK FOR SHORT IN CAN BUS LINES (ECM)
  1. Reconnect the ECM main bus line connector (I104) to the CAN No. 1 junction connector.

  1. Disconnect the ECM connector.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3

    Result:
    Result
    Proceed to
    OK (for 2GR-FE)
    A
    OK (for 2AR-FE)
    B
    NG
    C

    HINT:
    1. Measure the resistance with the combination meter assembly main bus line connector (I18) disconnected.
    2. If the resistance changes to 1 MΩ or more when the connector is disconnected, there may be a short in the ECM.



B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE CAN BUS MAIN LINES (ECM MAIN LINES)
A

REPLACE ECM (Click here)