Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is output, check the ignition coil assembly (No. 1 cylinder) circuit.
  3. If DTC P0352 is output, check the ignition coil assembly (No. 2 cylinder) circuit.
  4. If DTC P0353 is output, check the ignition coil assembly (No. 3 cylinder) circuit.
  5. If DTC P0354 is output, check the ignition coil assembly (No. 4 cylinder) circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A255924E01


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to the ECM while the engine is running (1 trip detection logic).
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil assembly and ECM
  3. Ignition coil assemblies (No. 1 to No. 4 cylinder)
  4. ECM

  1. A122717E29
    Reference: Inspection using an oscilloscope.
  2. While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
    ECM Terminal Name
    CH1: Between IGT (1 to 4) and E1
    CH2: Between IGF1 and E1
    Tester Range
    2 V/DIV., 20 ms./DIV.
    Condition
    Idling

MONITOR DESCRIPTION


A212405E10

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY


Required Sensors/Components (Main)
Igniter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / DTC.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0351, P0352, P0353 or P0354.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM


A266826E01


A266827E02


A255703E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
  1. Disconnect the ignition coil assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E37-4 (GND) - Body ground
    Always
    Below 1 Ω
    E40-4 (GND) - Body ground
    Always
    Below 1 Ω
    E38-4 (GND) - Body ground
    Always
    Below 1 Ω
    E43-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)


    A194110E68
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E37-1 (+B) - E37-4 (GND)
    Ignition switch ON
    11 to 14 V
    E40-1 (+B) - E40-4 (GND)
    Ignition switch ON
    11 to 14 V
    E38-1 (+B) - E38-4 (GND)
    Ignition switch ON
    11 to 14 V
    E43-1 (+B) - E43-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Coil Assembly)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E37-2 (IGF) - E26-51 (IGF1)
    Always
    Below 1 Ω
    E40-2 (IGF) - E26-51 (IGF1)
    Always
    Below 1 Ω
    E38-2 (IGF) - E26-51 (IGF1)
    Always
    Below 1 Ω
    E43-2 (IGF) - E26-51 (IGF1)
    Always
    Below 1 Ω
    E37-3 (IGT1) - E26-57 (IGT1)
    Always
    Below 1 Ω
    E40-3 (IGT2) - E26-56 (IGT2)
    Always
    Below 1 Ω
    E38-3 (IGT3) - E26-55 (IGT3)
    Always
    Below 1 Ω
    E43-3 (IGT4) - E26-54 (IGT4)
    Always
    Below 1 Ω
    E37-3 (IGT1) or E26-57 (IGT1) - Body ground
    Always
    10 kΩ or higher
    E40-3 (IGT2) or E26-56 (IGT2) - Body ground
    Always
    10 kΩ or higher
    E38-3 (IGT3) or E26-55 (IGT3) - Body ground
    Always
    10 kΩ or higher
    E43-3 (IGT4) or E26-54 (IGT4) - Body ground
    Always
    10 kΩ or higher
    E37-2 (IGF), E40-2 (IGF), E38-2 (IGF), E43-2 (IGF) or E26-51 (IGF1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

    NOTICE:
    Do not change the location of the connectors.

  1. Perform a simulation test.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B

    HINT:
    Perform "Inspection After Repair" after replacing the ignition coil assembly (Click here).



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
  1. Disconnect the ignition coil assembly connectors.

  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E37-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E40-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E38-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E43-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E37-1 (+B), E40-1 (+B), E38-1 (+B), E43-1 (+B) or 1A-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)