Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Navigation ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Navigation ECU Communication Stop Mode
Either condition is met:
  1. "Display and Navigation (AVN1)" is not displayed on the "Communication Bus Check" screen of the intelligent tester (Click here)
  2. Communication system DTCs (DTCs that start with U) that are output correspond to "Navigation ECU Communication Stop Mode" in "DTC Combination Table" (Click here)
  1. Navigation ECU sub-assembly branch line or connector
  2. Power source circuit of navigation ECU sub-assembly
  3. Navigation ECU sub-assembly ground circuit
  4. Navigation ECU sub-assembly

WIRING DIAGRAM


C240957E25


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON and wait at least 31 seconds.
  6. After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR OPEN IN CAN BUS LINES (NAVIGATION ECU SUB-ASSEMBLY BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C240580E05
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-9 (CANH) - I67-10 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation ECU Sub-assembly)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
  1. Disconnect the navigation ECU sub-assembly connector.



    C241290E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I64-7 (GND1) - Body ground
    Cable disconnected from negative (-) battery terminal
    Below 1 Ω

  1. Connect the cable to the negative (-) battery terminal.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I64-3 (ACC1) - Body ground
    Ignition switch ACC
    11 to 14 V
    I64-4 (+B1) - Body ground
    Ignition switch off
    11 to 14 V
    I67-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation ECU Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)