AIR CONDITIONING UNIT > INSTALLATION |
| 1. INSTALL AIR CONDITIONING UNIT ASSEMBLY |
Install the air conditioning unit assembly to the instrument panel reinforcement assembly with the 3 bolts.

| 2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT |
Engage the 3 guides and install the instrument panel reinforcement with air conditioning unit as shown in the illustration.

Install the instrument panel reinforcement assembly with the 3 bolts <A> and 2 new bolts <B> in the order shown in the illustration.

| *1 | Movable Collar | *2 | Body |
| *3 | Instrument Panel Reinforcement | - | - |
| *a | Step 1 | *b | Step 2 |
| *c | Step 3 | *d | Step 4 |
Pass the cooler drain hose through the vehicle securely.
Install the bolt.
Install the instrument panel reinforcement assembly with air conditioning unit with the nut.
![]() |
Install the instrument panel reinforcement assembly with the bolt <A> and bolt <B> in the order shown in the illustration.
Engage each clamp.
Connect the connector.
Connect the connector holder with the 2 nuts.
Install the bolt and connect the earth wire.
Connect the connector.
Install the 2 bolts and connect the 2 earth wires.
Engage each clamp.
for Power Tilt and Power Telescopic Steering Column:
Connect the protector with the nut.
Engage the claw and connect the airbag connector as shown in the illustration.

![]() |
Engage the 2 claws to lock the retainer as shown in the illustration.
| *1 | Retainer |
![]() |
Engage each clamp.
| *A | w/ Smart Entry and Start System |
| *1 | Airbag Sensor Assembly |
Connect each connector.
Connect the connector to the airbag sensor assembly as shown in the illustration.
![]() |
Engage the 3 claws to close the 3 clamps as shown in the illustration.
for 10 Speakers:
Engage the 3 clamps.
| 3. INSTALL FRONT LOWER PANEL PACKING |
![]() |
Install the 2 front lower panel packings shown in the illustration.
| 4. INSTALL INSTRUMENT PANEL SAFETY PAD CAP |
![]() |
Install the 5 new instrument panel safety pad caps.
| *A | for Driver Side |
| *B | for Passenger Side |
| 5. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
Install the screw and 2 nuts.
Install the No. 2 instrument panel brace sub-assembly with the bolt.
Connect the earth wire with the bolt.
Engage each clamp.
Connect the connector.
| 6. INSTALL INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY |
Install the screw and 2 nuts.
Install the instrument panel to cowl brace sub-assembly with the bolt.
Connect the earth wire with the bolt.
Engage each clamp.
Connect each connector.
| 7. INSTALL NO. 1 CONSOLE BOX DUCT |
Install the No. 1 console box duct with the clip.
| 8. INSTALL REAR NO. 3 AIR DUCT |
Engage the 2 claws to install the rear No. 3 air duct.
| 9. INSTALL FLOOR CARPET BRACKET LH |
Engage the 2 guides.
Install the floor carpet bracket LH with the 2 clips.
| 10. INSTALL REAR NO. 4 AIR DUCT |
![]() |
Engage the 4 claws to install the rear No. 4 air duct as shown in the illustration.
![]() |
Engage the guide to install the floor carpet to the original position as shown in the illustration.
| 11. CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Engage the guide to connect the fuel lid lock open lever sub-assembly as shown in the illustration.
Install the screw.
| 12. INSTALL REAR NO. 1 AIR DUCT |
Engage the 2 claws to install the rear No. 1 air duct.
| 13. INSTALL FLOOR CARPET BRACKET RH |
Engage the 2 guides.
Install the floor carpet bracket RH with the 2 clips.
| 14. INSTALL REAR NO. 2 AIR DUCT |
![]() |
Engage the 4 claws to install the rear No. 2 air duct as shown in the illustration.
![]() |
Engage the guide to install the floor carpet to the original position as shown in the illustration.
| 15. INSTALL FLOOR CARPET HOOK |
Engage the 6 claws to install the 6 floor carpet hooks.
Engage the 6 guides.
| 16. INSTALL WINDSHIELD WIPER RELAY ASSEMBLY |
Install the windshield wiper relay assembly with the nut.
Connect the connector.
| 17. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY |
Engage the 2 guides.
Install the air conditioning amplifier assembly with the 2 screws.
Connect each connector.
| 18. INSTALL ECU INTEGRATION BOX RH |
Install the ECU integration box RH with the 2 nuts and bolt.
Connect each connector.
| 19. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD) |
![]() |
Engage the claw to install the connector as shown in the illustration.
![]() |
Engage the claw to lock the connector lock as shown in the illustration.
![]() |
Engage the claw to connect the connector as shown in the illustration.
Install the instrument panel junction block assembly with the bolt and 2 nuts.
Connect each connector.
| 20. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD) |
![]() |
Engage the claw to install the connector as shown in the illustration.
![]() |
Engage the claw to lock the connector lock as shown in the illustration.
![]() |
Engage the claw to connect the connector as shown in the illustration.
Engage the claw to install the wiring harness clamp bracket.
Install the nut.
Install the instrument panel junction block assembly with the bolt and nut.
Connect each connector.
| 21. INSTALL STEERING POST ASSEMBLY |
| 22. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
| 23. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers) |
Engage the 2 guides to the vehicle body to temporarily install the stereo component amplifier assembly with bracket.
Install the stereo component amplifier assembly with bracket with the bolt.
Engage the clamp.
Connect each connector.
Connect the ground wire with the bolt.
| 24. INSTALL AUDIO AMPLIFIER COVER (for 10 Speakers) |
Install the audio amplifier cover with the 2 clips.
| 25. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat) |
| 26. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat) |
| 27. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat) |
| 28. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat) |
| 29. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
Remove the vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioning tube and accessory assembly.
Install the O-ring to the air conditioner tube and accessory assembly.
Install the air conditioner tube and accessory assembly.
| 30. CONNECT SUCTION PIPE SUB-ASSEMBLY |
Remove the vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.
Install the O-ring to the suction pipe sub-assembly.
![]() |
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 31. CONNECT HEATER INLET WATER HOSE |
Using pliers, grip the claws of the clip and slide the clip to connect the inlet water hose.
| 32. CONNECT HEATER OUTLET WATER HOSE |
Using pliers, grip the claws of the clip and slide the clip to connect the heater outlet water hose.
| 33. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 34. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 35. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 36. ADD ENGINE COOLANT (for 1AZ-FE) |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
Maintain the engine speed at 2000 to 2500 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 37. ADD ENGINE COOLANT (for 2AR-FE) |
Tighten the radiator drain cock plug by hand.
![]() |
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| *a | Code Mark |
| Code Mark "M" | 6.9 liters (7.3 US qts, 6.1 lmp. qts) |
| Code Mark "G" | 7.0 liters (7.4 US qts, 6.2 lmp. qts) |
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 38. ADD ENGINE COOLANT (for 2GR-FE) |
Tighten the radiator drain cock plug by hand.
![]() |
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| *a | Code Mark |
| Code Mark "M" | 6.9 liters (7.3 US qts, 6.1 lmp. qts) |
| Code Mark "G" | 7.0 liters (7.4 US qts, 6.2 lmp. qts) |
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 39. INSPECT FOR COOLANT LEAK (for 1AZ-FE) |
![]() |
Fill the radiator assembly with engine coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator assembly to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 40. INSPECT FOR COOLANT LEAK (for 2AR-FE) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 41. INSPECT FOR COOLANT LEAK (for 2GR-FE) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 42. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 43. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 44. INSPECT FOR REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 45. INITIALIZATION SERVO MOTOR |