Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1855/63    Short in Rear Side Squib LH Circuit

DTC    B1856/63    Open in Rear Side Squib LH Circuit

DTC    B1857/63    Short to GND in Rear Side Squib LH Circuit

DTC    B1858/63    Short to B+ in Rear Side Squib LH Circuit

for Preparation Click here


DESCRIPTION

The rear side squib LH circuit consists of the airbag sensor assembly and rear seat airbag assembly LH.
The circuit instructs SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the rear side squib LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1855/63
  1. The airbag sensor assembly receives a line short circuit signal in the rear side squib LH circuit during primary check.
  2. Rear side squib LH malfunction
  3. Airbag sensor assembly malfunction
  1. Floor wire
  2. Rear seat airbag assembly LH (Rear side squib LH)
  3. Airbag sensor assembly
B1856/63
  1. The airbag sensor assembly receives an open circuit signal in the rear side squib LH circuit.
  2. Rear side squib LH malfunction
  3. Airbag sensor assembly malfunction
B1857/63
  1. The airbag sensor assembly receives a short circuit to ground signal in the rear side squib LH circuit.
  2. Rear side squib LH malfunction
  3. Airbag sensor assembly malfunction
B1858/63
  1. The airbag sensor assembly receives a short circuit to B+ signal in the rear side squib LH circuit.
  2. Rear side squib LH malfunction
  3. Airbag sensor assembly malfunction

WIRING DIAGRAM


C239249E73


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

1.CHECK CONNECTORS


    C238350E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the rear seat airbag assembly LH and airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the rear seat airbag assembly LH and airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.

    Text in Illustration 
    *1
    Rear Seat Airbag Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire



NG
REPLACE FLOOR WIRE
OK


2.CHECK REAR SEAT AIRBAG ASSEMBLY LH (REAR SIDE SQUIB LH)


    C238351E06
  1. Connect the connector to the airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the rear seat airbag assembly LH (rear side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting it.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1855/63, B1856/63, B1857/63 or B1858/63 is not output.

    HINT:
    Codes other than DTCs B1855/63, B1856/63, B1857/63 and B1858/63 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector C.
    Text in Illustration 
    *1
    Rear Seat Airbag Assembly LH
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Rear Seat Airbag Assembly LH)



NG
Go to step 3
OK

REPLACE REAR SEAT AIRBAG ASSEMBLY LH (Click here)  

3.CHECK FLOOR WIRE


    C238352E06
  1. Disconnect the floor wire from the airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      Nz2-1 (SRL+) - Body ground
      Ignition switch ON
      Below 1 V
      Nz2-2 (SRL-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Nz2-1 (SRL+) - Nz2-2 (SRL-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Nz2-1 (SRL+) - Body ground
      Always
      1 MΩ or higher
      Nz2-2 (SRL-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Nz2-1 (SRL+) - Nz2-2 (SRL-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Rear Seat Airbag Assembly LH
      *2
      Airbag Sensor Assembly
      *3
      Floor Wire
      *a
      Front view of wire harness connector
      (to Rear Seat Airbag Assembly LH)



NG
REPLACE FLOOR WIRE
OK


4.CHECK DTC


    C238353E01
  1. Connect the connectors to the rear seat airbag assembly LH and airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1855/63, B1856/63, B1857/63 or B1858/63 is not output.

    HINT:
    Codes other than DTCs B1855/63, B1856/63, B1857/63 and B1858/63 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Rear Seat Airbag Assembly LH
    *2
    Airbag Sensor Assembly



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)