STEERING LOCK SYSTEM > Unable to Unlock Steering Wheel (Engine cannot Start) |
| Problem Symptom | Data List Item | Active Test Item |
| Unable to unlock steering wheel (Engine cannot start) | Entry&Start
| - |

| 1.CHECK DTC (ALL) |
Using the intelligent tester, confirm the output of DTCs for all systems.
|
| ||||
| OK | |
| 2.CHECK ENGINE SWITCH (SWITCH CONDITION) |
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (UNLOCK REQUEST RECEIVE) |
Use the Data List to check if the steering lock request is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Unlock Request Receive*1 | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
| OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine NG: Except above |
|
| Unlock Request Receive*2 | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) / OK or NG
| OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine NG: Except above |
|
| Result | Proceed to |
| OK | A |
| NG (w/ wireless door lock buzzer answer back function) | B |
| NG (w/o wireless door lock buzzer answer back function) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL) |
Disconnect the I24 steering lock ECU connector.
![]() |
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I24-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| I24-7 (B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Steering Lock ECU (Steering Lock Actuator Assembly)) |
|
| ||||
| OK | |
| 5.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL) |
Reconnect the I24 steering lock ECU connector.
![]() |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
| Tester Connection | I24-3 (IGE) - I24-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating |
| *a | Component with harness connected (Steering Lock ECU (Steering Lock Actuator Assembly)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
|
| ||||
| OK | ||
| ||
| 6.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK) |
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | |
| 7.REPLACE STEERING LOCK ACTUATOR ASSEMBLY |
Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).
Perform registration (refer to Service Bulletin).
Turn the engine switch on (IG).
Turn the steering wheel and check the steering condition.
|
| ||||
| OK | ||
| ||
| 8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if S code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | ||
| ||
| 9.READ VALUE USING INTELLIGENT TESTER (S CODE CHECK) |
Use the Data List to check if S code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | |
| 10.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK) |
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | |
| 11.REPLACE STEERING LOCK ACTUATOR ASSEMBLY |
Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).
Perform registration (refer to Service Bulletin).
Turn the engine switch on (IG).
Turn the steering wheel and check the steering condition.
|
| ||||
| OK | ||
| ||
| 12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if S code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | ||
| ||
| 13.REPLACE STEERING LOCK ACTUATOR ASSEMBLY |
Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).
Perform registration (refer to Service Bulletin).
Use the Data List to check if L code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | ||
| ||