Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > REMOVAL

for Preparation Click here


HINT:
  1. The following procedure is for the No. 1 parking brake cable assembly and No. 3 parking brake cable assembly.
  2. Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.



1. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY (for LHD)
(Click here)


2. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY (for RHD)
(Click here)


3. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)


    C239385
  1. Pull up the parking brake pedal claw.

    NOTICE:
    Do not damage the No. 1 parking brake cable assembly.



    C239384
  1. Remove the adjusting nut.



    C239386
  1. Remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.



4. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for RHD)


    C240112
  1. Pull up the parking brake pedal claw.

    NOTICE:
    Do not damage the No. 1 parking brake cable assembly.



    C240111
  1. Remove the adjusting nut.



    C240113
  1. Remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.



5. REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY


    C240114E01
  1. Separate the No. 3 parking brake cable assembly from the parking brake equalizer.
    Text in Illustration 
    *1
    Parking Brake Equalizer
    *2
    No. 2 Parking Brake Cable Assembly
    *3
    No. 3 Parking Brake Cable Assembly
    *4
    No. 4 Parking Brake Cable Assembly

  1. Separate the No. 2 parking brake cable assembly to remove the parking brake equalizer.



    C240115E01
  1. Slide the parking brake equalizer and rubber boot.
    Text in Illustration 
    *1
    Rubber Boot
    *2
    Parking Brake Equalizer
    *3
    No. 4 Parking Brake Cable Assembly

  1. Remove the No. 4 parking brake cable assembly from the parking brake equalizer.



6. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. for 2AR-FE: (Click here)
  2. for 1AZ-FE: (Click here)


7. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR


  1. for 2AR-FE, 1AZ-FE:



      C239390
    1. Remove the 3 nuts and front No. 2 floor heat insulator.



8. SEPARATE PARKING BRAKE SHOE LEVER
(Click here)


9. REMOVE NO. 2 FLOOR UNDER COVER (for LH Side)


    C240547
  1. Remove the 2 clips.
    Text in Illustration 
    V100135
    Nut (attached to under cover)

  1. Disengage the 6 nuts and remove the No. 2 floor under cover.

    HINT:
    The 6 nuts will remain attached to the No. 2 floor under cover.



10. REMOVE NO. 1 FLOOR UNDER COVER (for RH Side)


    C240546
  1. Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.
    Text in Illustration 
    V100135
    Nut (attached to under cover)

    HINT:
    Rotate the clips to disengage them. The 5 nuts and 2 clips will remain attached to the No. 1 floor under cover.



11. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C240116
  1. Remove the clip from the No. 3 parking brake cable assembly.



    C240117
  1. Remove the 2 bolts and separate the No. 3 parking brake cable assembly.



  1. Remove the 4 bolts, nut and No. 3 parking brake cable assembly.


    C240118



12. REMOVE NO. 2 PARKING BRAKE CABLE CLAMP
  1. Remove the No. 2 parking brake cable clamp from the No. 3 parking brake cable assembly.