Home › Engine / Hybrid System ยท 1AZ-FE › INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL INTAKE MANIFOLD
  1. Install the vacuum hose clamp with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Install a new No. 1 intake manifold to head gasket to the intake manifold.

  1. Set the intake manifold on the engine assembly.

  1. Using an E7 "TORX" wrench, install the 2 stud bolts.

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }

  1. Temporarily install the intake manifold with the 5 bolts and 2 nuts.



    A226738E03
  1. Tighten the 5 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Connect the oxygen sensor connector and 2 wire harness clamps.



2. CONNECT UNION TO VACUUM TUBE HOSE
  1. Connect the union to vacuum tube hose to the intake manifold.



3. CONNECT NO. 2 VENTILATION HOSE
  1. Connect the No. 2 ventilation hose to the intake manifold.



4. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    A147098
  1. Install 4 new injector vibration insulators to the cylinder head.

  1. Install the 2 fuel delivery spacers onto the cylinder head.

  1. Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies and install the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    1. Do not drop the fuel injector assemblies when installing the fuel delivery pipe sub-assembly.
    2. Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe sub-assembly.

  1. Connect the 4 fuel injector connectors.

  1. Install the 2 wire harness clamps.



5. CONNECT FUEL TUBE SUB-ASSEMBLY


    A261677E02
  1. Push the fuel tube connector to the fuel pipe until the fuel tube connector makes a "click" sound.
    Text in Illustration 
    *1
    Fuel Pipe
    *2
    Fuel Tube Connector
    *3
    Nylon Tube
    *4
    O-ring
    *5
    Retainer

    NOTICE:
    1. Before connecting the fuel tube connector and fuel pipe, check that there is no damage or foreign matter on the connecting part of the fuel pipe.
    2. After connecting the fuel tube connector and fuel pipe, check that they are securely connected by trying to pull them apart.

  1. Install the fuel tube sub-assembly to the fuel hose clamp.

  1. Install the No. 1 fuel pipe clamp.



6. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY
(Click here)


7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the intelligent tester on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.