Home › Power Source / Network · NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2325    LIN Communication Bus Malfunction

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No.
DTC Detection Condition
Trouble Area
B2325
Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
  1. Power window regulator motor assembly (for driver door)
  2. Power window regulator motor assembly (for front passenger door)
  3. Power window regulator motor assembly (for rear RH door)
  4. Power window regulator motor assembly (for rear LH door)
  5. Multiplex network master switch assembly
  6. Sliding roof ECU (sliding roof drive gear sub-assembly)*
  7. Main body ECU (multiplex network body ECU)
  8. Instrument panel junction block assembly
  9. Wire harness or connector
  1. *: w/ Sliding Roof System

WIRING DIAGRAM


B281972E03


INSPECTION PROCEDURE

NOTICE:
  1. When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization (Click here).
  2. When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (Click here).
  3. When using the intelligent tester to troubleshoot with the ignition switch off:
    Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (DRIVER DOOR) - MASTER SWITCH)
  1. Disconnect the K3*1 or J3*2 multiplex network master switch connector.

  1. Disconnect the K9*1 or J9*2 power window regulator motor (for driver door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K3-16 (LIN2) - K9-9 (LIN)*1
    J3-16 (LIN2) - J9-9 (LIN)*2
    Always
    Below 1 Ω
    K3-16 (LIN2) - Body ground*1
    J3-16 (LIN2) - Body ground*2
    Always
    10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


    B203350E07
  1. Remove the multiplex network master switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    16 (LIN2) - 17 (LIN1)
    Always
    Below 1 Ω
    16 (LIN2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Multiplex Network Master Switch Assembly)



NG
REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)
OK


3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the instrument panel junction block assembly (Click here).


    B281973E01

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3C-26 (LIN2) - MB-16 (LIN2)
    Always
    Below 1 Ω
    3B-30 (LIN2) - MB-16 (LIN2)
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *b
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *c
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (INSTRUMENT JUNCTION BLOCK - EACH ECU)
  1. Disconnect the J9*1, K9*2, K3*1, J3*2, S4*3, L2 and M2 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-26 (LIN2) - M2-9 (LIN)
    Always
    Below 1 Ω
    3B-30 (LIN2) - L2-9 (LIN)
    Always
    Below 1 Ω
    3B-30 (LIN2) - K3-17 (LIN1)*1
    3B-30 (LIN2) - J3-17 (LIN1)*2
    Always
    Below 1 Ω
    3B-30 (LIN2) - J9-9 (LIN)*1
    3B-30 (LIN2) - K9-9 (LIN)*2
    Always
    Below 1 Ω
    3B-30 (LIN2) - S4-11 (MPX1)*3
    Always
    Below 1 Ω
    3C-26 (LIN2) - Body ground
    Always
    10 kΩ or higher
    3B-30 (LIN2) - Body ground
    Always
    10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD
    3. *3: w/ Sliding Roof System



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR))
  1. Reconnect the K3*1, J3*2, 3B, 3C, S4*3, L2, K9*1, J9*2, J9*1 and K9*2 connectors.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    1. *1: for LHD
    2. *2: for RHD
    3. *3: w/ Sliding Roof System

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) (Click here)
A


6.CHECK DTC OUTPUT (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
  1. Reconnect the M2 connector.

  1. Disconnect the K3*1 or J3*2 connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    1. *1: for LHD
    2. *2: for RHD

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)
A


7.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR))
  1. Reconnect the K3*1 or J3*2 connector.

  1. Disconnect the L2 connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    1. *1: for LHD
    2. *2: for RHD

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) (Click here)
A


8.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))
  1. Reconnect the L2 connector.

  1. Disconnect the K9*1 or J9*2 connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    1. *1: for LHD
    2. *2: for RHD

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)
A


9.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR))
  1. Reconnect the K9*1 or J9*2 connector.

  1. Disconnect the J9*1 or K9*2 connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    1. *1: for LHD
    2. *2: for RHD

    Result:
    Result
    Proceed to
    DTC B2325 is output (w/ Sliding Roof System)
    A
    DTC B2325 is output (w/o Sliding Roof System)
    B
    DTC B2325 is not output
    C



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

C
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)
A


10.CHECK DTC OUTPUT (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))
  1. Reconnect the J9*1 or K9*2 connector.

  1. Disconnect the S4 connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    1. *1: for LHD
    2. *2: for RHD

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)