DTC P0010 Camshaft Position "A" Actuator Circuit (Bank 1) |
DTC P0020 Camshaft Position "A" Actuator Circuit (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0010 | Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 1) circuit (1 trip detection logic). |
|
| P0020 | Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 2) circuit (1 trip detection logic). |
|
| Related DTCs | P0010: Camshaft timing oil control valve assembly (for intake camshaft of bank 1) range check P0020: Camshaft timing oil control valve assembly (for intake camshaft of bank 2) range check |
| Required Sensors/Components (Main) | Camshaft timing oil control valve assembly (for intake camshaft) |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Starter | Off |
| Engine switch | On (IG) |
| Time after engine switch off to on (IG) | 0.5 seconds or more |
| One of the following conditions is met | A, B or C |
| A. All of the following conditions are met | - |
| Battery voltage | 11 V or higher, and less than 13 V |
| Target duty cycle | Less than 70% |
| Output duty cycle | 100% or higher |
| B. All of the following conditions are met | - |
| Battery voltage | 13 V or higher |
| Target duty cycle | Less than 80% |
| Output duty cycle | 100% or higher |
| C. Both of the following conditions are met | - |
| Current cut status | Not cut |
| Output duty cycle | 3% or less |
| Output duty cycle | Higher than 3%, and less than 100% |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ OUTPUT DTC (DTC P0010 OR P0020) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Clear the DTC after recording the freeze frame data and DTC (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and wait 5 seconds.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0010 or P0020 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for intake camshaft) (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E58-1 - E26-35 (OC1+) | Always | Below 1 Ω |
| E58-2 - E26-5 (OC1-) | Always | Below 1 Ω |
| E62-1 - E26-34 (OC2+) | Always | Below 1 Ω |
| E62-2 - E26-4 (OC2-) | Always | Below 1 Ω |
| E58-1 or E26-35 (OC1+) - Body ground | Always | 10 kΩ or higher |
| E58-2 or E26-5 (OC1-) - Body ground | Always | 10 kΩ or higher |
| E62-1 or E26-34 (OC2+) - Body ground | Always | 10 kΩ or higher |
| E62-2 or E26-4 (OC2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||