Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

DTC    B2784    Antenna Coil Open / Short

for Preparation Click here


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2784
The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*).
  1. Terminal AGND, VC5, TXCT or CODE is open (includes disconnection of the engine switch).
  2. The transponder key amplifier coil built into the engine switch is open.
  1. Engine switch
  2. Wire harness or connector
  3. Certification ECU (smart key ECU assembly)
With the shift lever in P, the key held near the engine switch and an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B2784
-

WIRING DIAGRAM


B271004E04


INSPECTION PROCEDURE

NOTICE:
  1. Before replacing the certification ECU (smart key ECU assembly), refer to Registration (Click here).
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
  1. Disconnect the I78 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the I58 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I78-7 (CODE) - I58-8 (CODE)
    Always
    Below 1 Ω
    I78-9 (TXCT) - I58-7 (TXCT)
    Always
    Below 1 Ω
    I78-1 (VC5) - I58-10 (VC5)
    Always
    Below 1 Ω
    I78-24 (AGND) - I58-6 (AGND)
    Always
    Below 1 Ω
    I58-8 (CODE) - Body ground
    Always
    10 kΩ or higher
    I58-7 (TXCT) - Body ground
    Always
    10 kΩ or higher
    I58-10 (VC5) - Body ground
    Always
    10 kΩ or higher
    I58-6 (AGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE ENGINE SWITCH
  1. Temporarily replace the engine switch with a new or known good one (Click here for 2GR-FE, Click here for 2AR-FE).


NEXT


3.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


4.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2784 is not output.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK

END (ENGINE SWITCH WAS DEFECTIVE)