Home › Engine / Hybrid System ยท 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):
  1. (a) The vehicle speed is 20 km/h (12.43 mph) or more.
  2. (b) The engine speed is 1000 rpm or higher.
  3. (c) The STA signal is on.
  1. Starter signal circuit
  2. Park/Neutral position switch assembly
  3. ECM

MONITOR STRATEGY


Related DTCs
P0617: Verify starter signal
Required Sensors/Components (Main)
ST relay
Park/Neutral position switch assembly
Certification ECU (smart key ECU assembly)
Required Sensors/Components (Related)
Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
20 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not stored
None
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Vehicle speed
20 km/h (12.43 mph) or more
Engine speed
1000 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS


Starter
On

CONFIRMATION DRIVING PATTERN


A231469E14

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the Techstream on [A].
  6. Start the engine.
  7. Idle the engine for 5 seconds or more [B].
  8. Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [D].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: P0617.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  14. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A266391E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Primary / Starter Signal.

  1. Check the value displayed on the Techstream when the vehicle is driven at 20 km/h (12.4 mph) or more.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.


    Result 
    Condition
    Techstream Display
    Proceed to
    Driving at 20 km/h (12.4 mph) or more
    Close (Starter signal off)
    A
    Open (Starter signal on)
    B



B
Go to step 2
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
  1. Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM - certification ECU (smart key ECU assembly)).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0617 is output
    B



B
REPLACE ECM (Click here)
A

END