DTC P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2714 | The ECM detects a malfunction in the shift solenoid valve SLT (ON side) according to the difference in the speed between the turbine and the output shaft, and also by the transmission fluid pressure. (2-trip detection logic) |
|
| Related DTCs | P2714: Shift solenoid valve SLT/ON malfunction |
| Required sensors/Components | Shift solenoid valve SLT |
| Frequency of operation | Continuous |
| Duration | 2 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. (Not circuit malfunction) | P0712, P0713 (ATF temperature sensor circuit (TFT sensor)) P0115, P0117, P0118 (ECT sensor circuit) P0715, P0717 (Turbine speed sensor circuit) P0791, P0793 (Intermediate shaft speed sensor circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0798 (Shift solenoid valve SL3 circuit) P2810 (Shift solenoid valve SL4 circuit) P2716 (Shift solenoid valve SLT circuit) P0327, P0328, (KCS sensor circuit) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 ((ETCS) Electronic throttle control system) U0100 (CAN communication system) |
| Transmission range | "D" |
| TFT (Transmission fluid temperature) | -10°C (14°F) or more |
| TFT (Transmission fluid temperature) sensor circuit | No circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | No circuit malfunction |
| Turbine speed sensor circuit | No circuit malfunction |
| Intermediate shaft speed sensor circuit | No circuit malfunction |
| Shift solenoid valve SL1 circuit | No circuit malfunction |
| Shift solenoid valve SL2 circuit | No circuit malfunction |
| Shift solenoid valve SL3 circuit | No circuit malfunction |
| Shift solenoid valve SL4 circuit | No circuit malfunction |
| Shift solenoid valve SLT circuit | No circuit malfunction |
| (KCS) Knock control sensor circuit | No circuit malfunction |
| (ETCS) Electronic throttle control system | Not system down |
| CAN communication system | Not system down |
| Engine | Starting |
| Input turbine torque | 100 N*m or more |
| Turbine speed | 250 rpm or more |
| Output speed | 250 rpm or more |
| Detection criteria | Threshold |
| Turbine speed - Output speed x Gear ratio at output speed 1,000 rpm (Condition varies with output speed) | 75 rpm or more |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Display (DTC Output) | Proceed to |
| Only "P2714" is output | A |
| "P2714" and other DTCs are output | B |
|
| ||||
| B | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
Turn the ignition switch off.
Lift the vehicle up.
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the Techstream to the DLC3.
Start the engine.
Warm up the Automatic Transmission Fluid (ATF).
Measure the line pressure when the engine is idling.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Follow the instructions on the Techstream and perform the Active Test.
Measure the line pressure with SST.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operates shift solenoid SLT to raise the line pressure. | ON/OFF
| [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFTING TEST) |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operates the shift solenoid valves to allow gears to selected manually. |
| Can be used to check the operation of the shift solenoid valves. Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition]
|
Check the vehicle speed and the gear when the engine speed is 1000 rpm.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the ECM commanded gear and the actual gear.
| Actuator Gear during Malfunction | ECM Commanded Gear | Proceed to | ||||||
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid SL4 | Stuck ON*3 | 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid SLT | Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E |
| Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| E | |
| 4.INSPECT SHIFT SOLENOID VALVE SLT |
![]() |
Remove shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.
| *1 | Shift Solenoid Valve SLT |
|
| ||||
| OK | |
| 5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||