DTC P0776 Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0776 | The engine revs freely when 4th, 5th, or 6th gear is commanded (2-trip detection logic). When any of the following is detected twice (2-trip detection logic):
|
|
| Related DTCs | P0776: Shift solenoid valve SL2/OFF malfunction Shift solenoid valve SL2/ON malfunction |
| Required sensors/Components | Shift solenoid valve SL2, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | OFF malfunction 0.5 sec. ON malfunction 0.8 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. (Not circuit malfunction) | P0712, P0713 (ATF temperature sensor circuit (TFT sensor)) P0115, P0117, P0118 (ECT sensor circuit) P0715, P0717 (Turbine speed sensor circuit) P0791, P0793 (Intermediate shaft speed sensor circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0798 (Shift solenoid valve SL3 circuit) P2810 (Shift solenoid valve SL4 circuit) P0327, P0328, (KCS sensor circuit) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 ((ETCS) Electronic throttle control system) U0100 (CAN communication system) |
| Transmission range | "D" |
| TFT (Transmission fluid temperature) | -10°C (14°F) or more |
| TFT (Transmission fluid temperature) sensor circuit | No circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | No circuit malfunction |
| Turbine speed sensor circuit | No circuit malfunction |
| Intermediate shaft speed sensor circuit | No circuit malfunction |
| Shift solenoid valve SL1 circuit | No circuit malfunction |
| Shift solenoid valve SL2 circuit | No circuit malfunction |
| Shift solenoid valve SL3 circuit | No circuit malfunction |
| Shift solenoid valve SL4 circuit | No circuit malfunction |
| (KCS) Knock control sensor circuit | No circuit malfunction |
| (ETCS) Electronic throttle control system | Not system down |
| CAN communication system | Not system down |
| Engine | Starting |
| ECM selected gear | 4th, 5th or 6th |
| ECM indicated pressure value of SL2 | 1,200 kPa |
| Throttle valve opening angle | 3% or more |
| ECM selected gear | 1st |
| Vehicle speed | 1.2 mph (2 km/h) to 24.9 mph (40 km/h) |
| ECT (Engine coolant temperature) | 40°C (104°F) or more |
| Engine speed - Turbine speed | 50 rpm or more |
| ECM selected gear | 2nd |
| Throttle valve opening angle | 6.5% or more at engine speed 2,000 rpm (Varies with engine speed) |
| Vehicle speed | 1.2 mph (2 km/h) or more |
| ECT (Engine coolant temperature) | 40°C (104°F) or more |
| ECM selected gear | 3rd |
| Throttle valve opening angle | 6.5% or more at engine speed 2,000 rpm (Varies with engine speed) |
| Vehicle speed | 1.2 mph (2 km/h) or more |
| ECT (Engine coolant temperature) | 40°C (104°F ) or more |
| Input (turbine) speed-Intermediate shaft speed x Gear ratio | 1,000 rpm or more |
| Input (turbine) speed/Intermediate shaft speed when output speed less than 1,000 rpm | 0.976 to 1.113 |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0776) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Display (DTC Output) | Proceed to |
| Only "P0776" is output | A |
| "P0776" and other DTCs are output | B |
|
| ||||
| B | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Details | Control Range | Diagnostic Note |
| Control the Shift Position | Operates the shift solenoid valves to allow gears to selected manually. |
| Can be used to check the operation of the shift solenoid valves. Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (31 mph) or less |
Check the vehicle speed and the gear when the engine speed is 1000 rpm.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the ECM commanded gear and the actual gear.
| Actuator Gear during Malfunction | ECM Commanded Gear | Proceed to | ||||||
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid SL4 | Stuck ON*3 | 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid SLT | Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E |
| Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| B | |
| 3.INSPECT SHIFT SOLENOID VALVE SL2 |
![]() |
Remove shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.
| *1 | Shift Solenoid Valve SL2 |
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||