DTC P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2757 |
|
|
| Related DTCs | P2757: Shift solenoid valve SLU OFF malfunction |
| Required sensors/Components | Shift solenoid valve SLU |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (a): 3.5 sec. OFF malfunction (b): 0.05 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. (Not circuit malfunction) | P0712, P0713 (ATF temperature sensor circuit (TFT sensor)) P0115, P0117, P0118 (ECT sensor circuit) P0715, P0717 (Turbine speed sensor circuit) P0791, P0793 (Intermediate shaft speed sensor circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0798 (Shift solenoid valve SL3 circuit) P2810 (Shift solenoid valve SL4 circuit) P2759 (Shift solenoid valve SLU circuit) P2769, P2770 (Shift solenoid valve SL circuit) P0327, P0328, (KCS sensor circuit) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 ((ETCS) Electronic throttle control system) U0100 (CAN communication system) |
| ECT (Engine coolant temperature) | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0°CA or more |
| Transmission range | "D" |
| TFT (Transmission fluid temperature) | -10°C (14°F) or more |
| TFT (Transmission fluid temperature) sensor circuit | No circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | No circuit malfunction |
| Turbine speed sensor circuit | No circuit malfunction |
| Intermediate shaft speed sensor circuit | No circuit malfunction |
| Shift solenoid valve SL1 circuit | No circuit malfunction |
| Shift solenoid valve SL2 circuit | No circuit malfunction |
| Shift solenoid valve SL3 circuit | No circuit malfunction |
| Shift solenoid valve SL4 circuit | No circuit malfunction |
| Shift solenoid valve SLU circuit | No circuit malfunction |
| Shift solenoid valve SL circuit | No circuit malfunction |
| (KCS) Knock control sensor circuit | No circuit malfunction |
| (ETCS) Electronic throttle control system | Not system down |
| CAN communication system | Not system down |
| Engine | Starting |
| ECM selected gear | Not 1st |
| Vehicle speed | 15.5 mph (25 km/h) or more |
| Turbine speed/Output speed (NT/NO) with 1st | 3.232 to 7.556 |
| Turbine speed/Output speed (NT/NO) with 2nd | 1.860 to 2.289 |
| Turbine speed/Output speed (NT/NO) with 3rd | 1.369 to 1.613 |
| Turbine speed/Output speed (NT/NO) with 4th | 0.976 to 1.113 |
| Turbine speed/Output speed (NT/NO) with 5th | 0.690 to 0.818 |
| Turbine speed/Output speed (NT/NO) with 6th | 0.556 to 0.680 |
| ECM lock-up command | ON |
| Duration time from lock-up on command | 3 sec. or more |
| Following conditions are met | (a) and (b) |
| (a) Engine speed - Turbine speed | 70 rpm or more |
| (b) Transmission fluid pressure switch | OFF |
| Speed sensor (NT) | Input speed is equal to engine speed when lock-up is ON. |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Lock Up | Controls the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition. | ON/OFF | Can be used to check SLU and SL solenoid operation. [Vehicle Condition]
|
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Display (DTC output) | Proceed to |
| Only "P2757" is output | A |
| "P2757" and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE SLU |
![]() |
Remove shift solenoid valve SLU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.
| *1 | Shift Solenoid Valve SLU |
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
|
| ||||
| OK | ||
| ||