DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |
DTC P0159 Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 | Either of the following conditions is met:
|
|
| P0137 P0157 | Either of the following conditions is met:
|
|
| P0138 P0158 |
|
|
| P0139 P0159 | Either of the following conditions is met:
|
|
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0136 P0156 | Not applicable | None |
| P0137 P0157 |
|
|
| P0138 P0158 | Not applicable | None |
| P0139 P0159 | Not applicable | None |
| Active Air Fuel Ratio Control |
| Abnormal Voltage Output of Heated Oxygen Sensor (DTCs P0136 and P0156) |

| Open in Heated Oxygen Sensor Circuit (DTCs P0137 and P0157) |

| High or Low Impedance of Heated Oxygen Sensor (DTCs P0136 and P0156 or P0137 and P0157) |
![]() |
| Extremely High Output Voltage of Heated Oxygen Sensor (DTCs P0138 and P0158) |
| Abnormal Voltage Output of Heated Oxygen Sensor During Fuel-cut (DTCs P0139 and P0159) |
| Related DTCs | P0136: Heated oxygen sensor (bank 1) voltage check (voltage malfunction) P0136: Heated oxygen sensor (bank 1) circuit continuity check (circuit short) P0137: Heated oxygen sensor (bank 1) voltage check (low voltage) P0137: Heated oxygen sensor (bank 1) circuit continuity check (circuit open) P0138: Heated oxygen sensor (bank 1) circuit continuity check (out of range) P0139: Heated oxygen sensor (bank 1) response rate during fuel cut P0156: Heated oxygen sensor (bank 2) voltage check (voltage malfunction) P0156: Heated oxygen sensor (bank 2) circuit continuity check (circuit short) P0157: Heated oxygen sensor (bank 2) voltage check (low voltage) P0157: Heated oxygen sensor (bank 2) circuit continuity check (circuit open) P0158: Heated oxygen sensor (bank 2) circuit continuity check (out of range) P0159: Heated oxygen sensor (bank 2) response rate during fuel cut |
| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Mass air flow meter sub-assembly Throttle position sensor Air fuel ratio sensor |
| Frequency of Operation | Once per driving cycle: Active air fuel ratio control detection, heated oxygen sensor abnormal voltage during fuel cut. Continuous: Other |
| Duration | 20 seconds: Heated oxygen sensor voltage check 30 seconds: Heated oxygen sensor circuit continuity check (circuit short) 90 seconds: Heated oxygen sensor circuit continuity check (circuit open) 10 seconds: Heated oxygen sensor circuit continuity check (out of range) 7 seconds: Heated oxygen sensor response rate during fuel cut |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0016, P0018 (VVT system - misalignment) P0017, P0019 (Exhaust VVT system - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0037, P0038, P0057, P0058, P102D, P105D (Heated oxygen sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient engine coolant temperature for closed loop fuel control) P0128 (Thermostat) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0451, P0452, P0453 (EVAP system) P0500 (Vehicle speed sensor) P219A, P219B (Air-fuel ratio imbalance) |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idling | Off |
| Engine speed | Less than 3200 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 70% |
| Shift position | 3rd or higher |
| Battery voltage | 11 V or higher |
| Estimated sensor temperature | Less than 700°C (1292°F) |
| ECM monitor | Completed |
| DTC P0607 | Not set |
| Battery voltage | 11 V or higher |
| Estimated sensor temperature | 450°C (842°F) or higher, and less than 750°C (1382°F) |
| DTC P0607 | Not set |
| Battery voltage | 11 V or higher |
| Time after engine start | 2 seconds or more |
| Engine coolant temperature | 75°C (167°F) or higher |
| Catalyst temperature | 400°C (752°F) or higher |
| Fuel cut | On |
| All of following conditions (a), (b) and (c) met | - |
| (a) OSC (Oxygen Storage Capacity) of catalyst | 2 g or more |
| (b) Heated oxygen sensor voltage | 0.21 V or higher, and less than 0.59 V |
| (b) Commanded air fuel ratio | 14.3 or less |
| All of following conditions (a), (b) and (c) met | - |
| (a) OSC (Oxygen Storage Capacity) of catalyst | 2 g or more |
| (b) Heated oxygen sensor voltage | Less than 0.21 V |
| (c) Commanded air fuel ratio | 14.3 or less |
| Duration of following condition | 30 seconds or more |
| Heated oxygen sensor impedance | Less than 5 Ω |
| Duration of following condition | 90 seconds or more |
| Heated oxygen sensor impedance | 15 kΩ or higher |
| Duration of following condition | 10 seconds or more |
| Heated oxygen sensor voltage | 1.2 V or higher |
| Either of the following conditions is met | - |
| Total airflow volume reached after start of fuel-cut while heated oxygen sensor voltage remains at 0.2 V or higher | More than 11.3 g |
| Duration until rear heated oxygen sensor voltage drops from 0.35 V to 0.2 V during fuel cut | 1 second or more |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $08 | Multiply by 0.001 | V | Maximum sensor voltage |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $8B | Multiply by 0.001 | Seconds | 0.35 - 0.2 V sensor switch time |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $8D | Multiply by 0.001 | Seconds | Duration that sensor voltage drops to 0.2 V during fuel-cut |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $8F | Multiply by 0.0003 | g | Maximum oxygen storage capacity |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $06 | $08 | Multiply by 0.001 | V | Maximum sensor voltage |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $06 | $8B | Multiply by 0.001 | Seconds | 0.35 - 0.2 V sensor switch time |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $06 | $8D | Multiply by 0.001 | Seconds | Duration that sensor voltage drops to 0.2 V during fuel-cut |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $06 | $8F | Multiply by 0.0003 | g | Maximum oxygen storage capacity |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 AFS Voltage B2S1 (Air fuel ratio) | +12% | Rich | Below 3.1 V |
| -12% | Lean | Higher than 3.4 V | |
| O2S B1S2 O2S B2S2 (Heated oxygen) | +12% | Rich | Higher than 0.55 V |
| -12% | Lean | Below 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0139, P0156, P0157, P0158 OR P0159) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0138 or P0158 is output | A |
| DTC P0137 or P0157 is output | B |
| DTC P0136 or P0156 is output | C |
| DTC P0139 or P0159 is output | D |
| DTC P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
Disconnect the heated oxygen sensor connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX2B) | Always | 10 kΩ or higher |
| *1 | Bank 1 | *2 | Bank 2 |
| *a | Component without harness connected (Heated Oxygen Sensor) | - | - |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the engine switch to off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-28 (HT1B) - E26-101 (OX1B) | Always | 10 kΩ or higher |
| E26-22 (HT2B) - E26-133 (OX2B) | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Gas AF Control / O2S B1S2 or O2S B2S2.
Change the fuel injection volume using the Techstream, and monitor the voltage output of the heated oxygen sensor displayed on the Techstream.
|
| ||||
| OK | |
| 5.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Gas AF Control / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Change the fuel injection volume using the Techstream, and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the Techstream.
| Techstream Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 AFS Voltage B2S1 (Air fuel ratio) | Alternates between higher and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 7.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-1 (HT1B) - E26-28 (HT1B) | Always | Below 1 Ω |
| E22-3 (OX1B) - E26-101 (OX1B) | Always | Below 1 Ω |
| E22-4 (E2) - E26-102 (EX1B) | Always | Below 1 Ω |
| E20-1 (HT2B) - E26-22 (HT2B) | Always | Below 1 Ω |
| E20-3 (OX2B) - E26-133 (OX2B) | Always | Below 1 Ω |
| E20-4 (E2) - E26-134 (EX2B) | Always | Below 1 Ω |
| E22-1 (HT1B) or E26-28 (HT1B) - Body ground | Always | 10 kΩ or higher |
| E22-3 (OX1B) or E26-101 (OX1B) - Body ground | Always | 10 kΩ or higher |
| E20-1 (HT2B) or E26-22 (HT2B) - Body ground | Always | 10 kΩ or higher |
| E20-3 (OX2B) or E26-133 (OX2B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 10.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0136, P0137, P0138, P0156, P0157 and P0158).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0156 OR P0157) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0136, P0137, P0156 or P0157.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0136, P0137, P0156 or P0157 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | ||
| ||
| 12.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0136, P0137, P0138, P0156, P0157 and P0158).
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0156) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0136 or P0156.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0136 or P0156 is output) | B |
|
| ||||
| A | ||
| ||
| 15.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 16.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
Turn the engine switch off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-28 (HT1B) - E26-101 (OX1B) | Always | 10 kΩ or higher |
| E26-22 (HT2B) - E26-133 (OX2B) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 17.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0139 and P0159).
| NEXT | |
| 18.READ OUTPUT DTC (DTC P0139 OR P0159 IS OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0139 or P0159.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0139 or P0159 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | ||
| ||