DTC P0340 Camshaft Position Sensor Circuit Malfunction |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 | When one of the following conditions is met:
|
|
| P0342 | The output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic). |
|
| P0343 | The output voltage is higher than 4.7 V for 4 seconds (1 trip detection logic). |
|
![]() |
| ECM Terminal Name | CH1: Between VV1+ and VV1- CH2: Between EV1+ and EV1- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
| Related DTCs | P0340: Camshaft position sensor verify pulse input P0342: Camshaft position sensor range check (low voltage) P0343: Camshaft position sensor range check (high voltage) |
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 4 seconds: Camshaft position sensor verify pulse input (case 1) (P0340), Camshaft position sensor range check (P0342, P0343) 5 seconds: Camshaft position sensor verify pulse input (case 2) (P0340) |
| MIL Operation | 2 driving cycles: Camshaft position sensor verify pulse input (case 1) (P0340) Immediate: Camshaft position sensor verify pulse input (case 2) (P0340), Camshaft position sensor range check (P0342, P0343) |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Both of the following conditions are met | - |
| Starter | On and not starter on again |
| Minimum battery voltage while starter on | Below 11 V |
| All of the following conditions are met | - |
| Engine speed | 600 rpm or higher |
| Starter | Off |
| Camshaft position sensor voltage | 0.3 to 4.7 V |
| VVT system misalignment | Not detected |
| Camshaft position sensor range check fail | Not detected |
| All of the following conditions are met | - |
| Starter | Off |
| Ignition switch | ON |
| Time after ignition switch turned from off to ON | 2 seconds or more |
| Battery voltage | 8 V or higher |
| Camshaft position sensor verify pulse input fail | Not detected |
| Camshaft position sensor signal | No signal |
| Either of the following conditions is met | 1 or 2 |
| 1. Camshaft position and crankshaft position phase | Misaligned |
| 2. Camshaft position sensor signal | No signal |
| Camshaft position sensor voltage | Below 0.3 V |
| Camshaft position sensor voltage | Higher than 4.7 V |
| Camshaft position sensor voltage | 0.3 to 4.7 V |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR) |
![]() |
Disconnect the camshaft position sensor for intake camshaft connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E55-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Camshaft Position Sensor for Intake Camshaft) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor for intake camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E55-1 (VV1+) - E26-82 (VV1+) | Always | Below 1 Ω |
| E55-2 (VV1-) - E26-114 (VV1-) | Always | Below 1 Ω |
| E55-1 (VV1+) or E26-82 (VV1+) - Body ground | Always | 10 kΩ or higher |
| E55-2 (VV1-) or E26-114 (VV1-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT) |
![]() |
Check the camshaft position sensor for intake camshaft installation.
|
| ||||
| OK | |
| 4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR) |
Check the timing rotor of the intake camshaft.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |

| *1 | Timing Mark | - | - |
Remove the cylinder head cover sub-assembly.
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) |
Replace the camshaft position sensor (for intake camshaft) (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0340, P0342 or P0343 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor for intake camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E55-3 (VC) - E26-113 (VCV1) | Always | Below 1 Ω |
| E55-3 (VC) or E26-113 (VCV1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||