DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic). |
|

| *1 | Air Fuel Ratio Sensor (Sensor 1) | *2 | Heated Oxygen Sensor (Sensor 2) |
| *3 | TWC: Front Catalyst | *4 | TWC: Rear Catalyst |
| *5 | Center Exhaust Pipe Assembly | *6 | Tail Exhaust Pipe Assembly |
| *7 | Exhaust Manifold Converter Sub-assembly | *8 | Front Exhaust Pipe Assembly |
| *a | for PZEV | - | - |

| *1 | Air Fuel Ratio Sensor (Sensor 1) | *2 | Heated Oxygen Sensor (Sensor 2) |
| *3 | TWC: Front Catalyst | *4 | TWC: Rear Catalyst |
| *5 | Center Exhaust Pipe Assembly | *6 | Tail Exhaust Pipe Assembly |
| *7 | Exhaust Manifold Converter Sub-assembly | *8 | Front Exhaust Pipe Assembly |
| *a | Except for PZEV | - | - |
| Related DTCs | P0420: Catalyst deterioration |
| Required Sensors/Components (Main) | Air fuel ratio sensor Heated oxygen sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor Mass air flow meter sub-assembly Crankshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Approximately 30 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0010 (VVT oil control valve) P0011 (VVT system - advance) P0012 (VVT system - retard) P0016 (VVT system - misalignment) P0013 (Exhaust camshaft timing oil control valve) P0014 (Exhaust VVT system - advance) P0015 (Exhaust VVT system - retard) P0017 (Exhaust VVT system - misalignment) P0031, P0032, P101D (Air fuel ratio sensor heater) P0037, P0038, P102D (Heated oxygen sensor heater) P0136, P0137, P0138, P0139, P0607 (Rear oxygen sensor) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0171, P0172 (Fuel system) P0301 - P0304 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0365, P0367, P0368 (Exhaust camshaft position sensor) P0351 - P0354 (Igniter) P0500 (Vehicle speed sensor) P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253, P2A00 (Air fuel ratio sensor) P219A (Air fuel ratio imbalance) |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idling | Off |
| Engine speed | Less than 3000 rpm (except PZEV) Less than 4000 rpm (for PZEV) |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 90% (except PZEV) 10% or higher, and less than 80% (for PZEV) |
| Shift position | 4th or higher (except PZEV) 5th or higher (for PZEV) |
| All of the following conditions are met | - |
| Mass air flow rate | 2.5 gm/sec or more, and less than 60 gm/sec (except PZEV) 2.5 gm/sec or more, and less than 40 gm/sec (for PZEV) |
| Front catalyst temperature (estimated) | 605°C (1121°F) or higher, and less than 870°C (1598°F) (except PZEV) 575°C (1067°F) or higher, and less than 810°C (1490°F) (for PZEV) |
| Rear catalyst temperature (estimated) | 400°C (752°F) or higher, and less than 770°C (1418°F) |
| Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC) | Less than 0.1523 g (except PZEV) Less than 0.1425 g (for PZEV) Less than 0.0957 g (for Mexico models) |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $21 | $A9 | Multiply by 0.0003 | No dimension | Oxygen storage capacity of catalyst bank 1 |



| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Turn the Techstream on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / GAS AF Control / AFS Voltage B1S1 and O2S B1S2.
Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | +12% | Rich | Below 3.1 V |
| -12% | Lean | Higher than 3.4 V | |
| O2S B1S2 (Heated oxygen) | +12% | Rich | Higher than 0.55 V |
| -12% | Lean | Below 0.4 V |
| Status AFS Voltage B1S1 | Status O2S B1S2 | Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - |
| B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - |
| |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - |
| |
| Lean | Lean | Actual air fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) |
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (Click here).
Replace the front exhaust pipe assembly (TWC: Rear catalyst) (Click here).
| NEXT | ||
| ||
| 5.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
|
| ||||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 7.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
|
| ||||
| 8.CHECK FOR EXHAUST GAS LEAK |
Check the exhaust gas leaks.
|
| ||||
| OK | |
| 9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .
|
| ||||
| 10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT |
Repair or replace exhaust gas leak point.
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC is not output (No pending DTCs output) | B |
|
| ||||
| A | |
| 12.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) |
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (Click here).
Replace the front exhaust pipe assembly (TWC: Rear catalyst) (Click here).
| NEXT | ||
| ||