DTC P2004 Intake Manifold Runner Control Stuck Open (Bank 1) |
DTC P2006 Intake Manifold Runner Control Stuck Closed (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2004 | The tumble control valve opening angle is 17 deg. or more after requesting the tumble control valve to fully close (2 trip detection logic). |
|
| P2006 | The tumble control valve opening angle is less than 35 deg. after requesting the tumble control valve to fully open (2 trip detection logic). |
|
| Control the IAC Duty Ratio Operation | Intake Air Control Position |
| 100% | Approximately 70 deg. |
| 0% | Approximately 70 deg. |
| -100% | Approximately 2 deg. |
| Related DTCs | P2004: Tumble Control Valve (TCV) stuck open P2006: Tumble Control Valve (TCV) stuck closed |
| Required Sensors/Components (Main) | Tumble control valve |
| Required Sensors/Components (Related) | Intake air temperature sensor Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Approximately 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Engine coolant temperature | -10°C (14°F) or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Ignition switch | ON |
| Battery voltage | 8 V or higher |
| Control valve angle when commanded closed | 17 deg. or more |
| Control valve angle when commanded open | Less than 35 deg. |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2004 OR P2006) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P2004 or P2006 is output | A |
| DTC P2004 or P2006 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE) |
Inspect the intake air control valve actuator (for tumble control valve) .
|
| ||||
| OK | |
| 3.INSPECT INTAKE MANIFOLD (TUMBLE CONTROL VALVE OPERATION) |
Inspect the intake manifold for the tumble control valve operation .
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM) |
Disconnect the ECM connector.
Disconnect the intake air control valve actuator connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y4-4 (M-) - E26-21 (IA1-) | Always | Below 1 Ω |
| Y4-5 (M+) - E26-22 (IA1+) | Always | Below 1 Ω |
| Y4-4 (M-) or E26-21 (IA1-) - Body ground | Always | 10 kΩ or higher |
| Y4-5 (M+) or E26-22 (IA1+) - body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2004 OR P2006) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P2004 or P2006 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||