Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P2009    Intake Manifold Runner Control Circuit Low (Bank 1)

DTC    P2010    Intake Manifold Runner Control Circuit High (Bank 1)

for Preparation Click here


DESCRIPTION

The ECM activates the intake air control valve actuator (for tumble control valve), which opens and closes the Tumble Control Valve (TCV). The ECM activates the DC motor based on engine speed, coolant temperature, intake air temperature and other conditions.

DTC No.
DTC Detection Condition
Trouble Area
P2009
Both of the following conditions continue for 1 second (1 trip detection logic).
(a) The output duty of the intake air control valve actuator is 100% or higher.
(b) The current of the intake air control valve actuator is less than 0.35 A.
  1. Open or short in intake air control valve actuator (for tumble control valve) circuit
  2. Intake air control valve actuator (for tumble control valve)
  3. Intake manifold
  4. ECM
P2010
Either of the following conditions continues for 6 times or more (1 trip detection logic).
(a) The motor drive IC has overcurrent.
(b) The motor drive IC overheats.
  1. Open or short in intake air control valve actuator (for tumble control valve) circuit
  2. Intake air control valve actuator (for tumble control valve)
  3. Intake manifold
  4. ECM

MONITOR DESCRIPTION

When the voltage of the intake air control valve actuator deviates from the standard range, the ECM determines that a malfunction has occurred and stores a DTC.

MONITOR STRATEGY


Related DTCs
P2009: Intake air control valve actuator for tumble control valve range check (low current)
P2010: Intake air control valve actuator for tumble control valve range check (high current)
Required Sensors/Components (Main)
Intake air control valve actuator (for tumble control valve)
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second: P2009
6 times: P2010
MIL Operation
Immediate
Sequence Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None

P2009 
All of the following conditions are met
-
Battery voltage
8 V or higher
Ignition switch
ON
Starter
Off
Output duty cycle
100% or higher
Difference between motor current and previous motor current
Less than 0.2 A

P2010 
All of the following conditions are met
-
Battery voltage
8 V or higher
Ignition switch
ON
Starter
Off

TYPICAL MALFUNCTION THRESHOLDS


P2009 
Intake air control valve actuator for tumble control valve current
Less than 0.35 A

P2010 
Motor drive IC high current limiter monitor input
Fail

COMPONENT OPERATING RANGE


P2009 
Intake air control valve actuator for tumble control valve current
Higher than 0.35 A

P2010 
Motor drive IC high current limiter monitor input
Pass

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
  8. Check that the engine coolant temperature is 60°C (140°F) or higher.
  9. Wait approximately 10 seconds.
  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  11. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P2009 or P2010.
  14. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  15. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2004 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)
  1. Inspect the intake air control valve actuator (for tumble control valve) (Click here).



NG
REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE) (Click here)
OK


2.INSPECT INTAKE MANIFOLD (TUMBLE CONTROL VALVE OPERATION)
  1. Inspect the intake manifold for the tumble control valve operation .



NG
REPLACE INTAKE MANIFOLD (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the intake air control valve actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Y4-4 (M-) - E26-21 (IA1-)
    Always
    Below 1 Ω
    Y4-5 (M+) - E26-22 (IA1+)
    Always
    Below 1 Ω
    Y4-4 (M-) or E26-21 (IA1-) - Body ground
    Always
    10 kΩ or higher
    Y4-5 (M+) or E26-22 (IA1+) - body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2009 OR P2010)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Wait approximately 10 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P2009 or P2010 is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)