DTC P2014 Intake Manifold Runner Position Sensor / Switch Circuit (Bank 1) |
DTC P2016 Intake Manifold Runner Position Sensor / Switch Circuit Low (Bank 1) |
DTC P2017 Intake Manifold Runner Position Sensor / Switch Circuit High (Bank 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2014 | The tumble control valve position sensor output voltage flutters up and down beyond the normal operating range (less than 0.2 V, or higher than 4.8 V) for more than 0.5 seconds (open or short) (1 trip detection logic). |
|
| P2016 | The tumble control valve position sensor output voltage is less than 0.2 V for more than 0.5 seconds (short) (1 trip detection logic). |
|
| P2017 | The tumble control valve position sensor output voltage is higher than 4.8 V for more than 0.5 seconds (open) (1 trip detection logic). |
|
| IAC Sensor Voltage | Malfunction |
| 0.2 V or less |
|
| 4.8 V or higher |
|
| Related DTCs | P2014: Tumble control valve position sensor range check (chattering) P2016: Tumble control valve position sensor range check (low voltage) P2017: Tumble control valve position sensor range check (high voltage) |
| Required Sensors/Components (Main) | Intake air control valve actuator (for tumble control valve) |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Tumble control valve position sensor voltage | Less than 0.2 V, or higher than 4.8 V |
| Tumble control valve position sensor voltage | Less than 0.2 V |
| Tumble control valve position sensor voltage | Higher than 4.8 V |
| Tumble control valve position sensor voltage | 0.2 to 4.8 V |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE IAC DUTY RATIO) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the IAC Duty Ratio / Gas Intake Control / IAC Sensor Voltage.
Check the value of IAC Sensor Voltage while changing Control the IAC Duty Ratio from -100 to 100% (or from 100 to -100%) using the Techstream.
| Control the IAC Duty Ratio Operation | IAC Sensor Voltage (Normal) | Suspected Trouble Area | ||
|
| Sensor malfunction | ||
| -100% | 0.2 to 1.4 V | Remains below 0.2 V | Remains higher than 4.8 V | Other than the voltage in the 2 columns on the left |
| 100% | 3.2 to 4.8 V | Remains below 0.2 V | Remains higher than 4.8 V | |
|
| ||||
| OK | |
| 2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P2014, P2016 and/or P2017 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM) |
Disconnect the ECM connector.
Disconnect the intake air control valve actuator connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y4-3 (VDD) - E26-130 (VCIA) | Always | Below 1 Ω |
| Y4-1 (OUT) - E26-131 (IAC1) | Always | Below 1 Ω |
| Y4-2 (GND) - E26-129 (EIA1) | Always | Below 1 Ω |
| Y4-3 (VDD) or E26-130 (VCIA) - Body ground | Always | 10 kΩ or higher |
| Y4-1 (OUT) or E26-131 (IAC1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR CONTROL VALVE ACTUATOR) |
![]() |
Disconnect the intake air control valve actuator connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Y4-3 (VDD) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Intake Air Control Valve Actuator) |
|
| ||||
| OK | |
| 5.REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE) |
Replace the intake air control valve actuator (for tumble control valve) (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P2014, P2016 and/or P2017 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||