Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1429    Open or Short in Brake Pedal Load Sensing Switch

for Preparation Click here


DESCRIPTION

The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level.
The skid control ECU uses this circuit to detect if the brake pedal is depressed or not.

DTC No.
DTC Detection Condition
Trouble Area
C1429
An open or short in the brake pedal load sensing switch circuit continues for 0.5 seconds or more.
  1. Brake pedal load sensing switch (Brake pedal support assembly)
  2. Brake pedal load sensing switch circuit
  3. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


C168343E08


INSPECTION PROCEDURE

HINT:
When C1249, C1425 and/or C1426 is output together with C1429, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first (Click here, Click here, and/or Click here).

1.READ VALUE USING TECHSTREAM (BRAKE PEDAL LOAD SENSING SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond a specified point
    OFF: Brake pedal not depressed beyond a specified point
    -

  1. Check that the brake pedal load sensing switch display observed on the Techstream changes according to brake pedal operation.

    OK:
    The Techstream displays ON or OFF according to brake pedal operation.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1429 is not output.
    A
    DTC C1429 is output.
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH


    C239141E01
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake pedal load sensing switch connector.

    NOTICE:
    1. Do not remove the brake pedal load sensing switch from the brake pedal support assembly.
    2. When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (FSW+) - 1 (FSW-)
    Switch OFF
    (Brake pedal depressed)
    950 to 1050 Ω
    2 (FSW+) - 1 (FSW-)
    Switch ON
    (Brake pedal released)
    203 to 223 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))



NG
REPLACE BRAKE PEDAL SUPPORT ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A49-34 (FSW+) - A40-2 (FSW+)
    Always
    Below 1 Ω
    A49-34 (FSW+) - Body ground
    Always
    10 kΩ or higher
    A40-1 (FSW-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)