Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TC and CG Terminal Circuit

for Preparation Click here


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning and slip indicator lights.

WIRING DIAGRAM


C243628E03


INSPECTION PROCEDURE

HINT:
When the indicator lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.INSPECT DLC3


    C207407E27
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I39-13 (TC) - I39-4 (CG)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 4
OK


3.REPLACE ECM


    C207407E27
  1. Turn the ignition switch off.

  1. Replace the ECM (Click here for 2GR-FE, or Click here for 2AR-FE).

  1. Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  
  1. Check that the ABS warning and slip indicator lights are blinking.

    OK:
    The ABS warning and slip indicator lights are blinking.

    Text in Illustration 
    *a
    Front view of DLC3

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

END 

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    I39-13 (TC) - A25-45 (TC)
    Always
    Below 1 Ω
    I39-13 (TC) - Body ground
    Always
    10 kΩ or higher
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    I39-13 (TC) - A25-23 (TC)
    Always
    Below 1 Ω
    I39-13 (TC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)


    C207407E18
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-4 (CG) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE ECM


    C207407E27
  1. Replace the ECM (Click here for 2GR-FE, or Click here for 2AR-FE).

  1. Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  
  1. Check that the ABS warning and slip indicator lights are blinking.

    OK:
    The ABS warning and slip indicator lights are blinking.

    Text in Illustration 
    *a
    Front view of DLC3

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

END