DTC P0365 Camshaft Position Sensor "B" Circuit (Bank 1) |
DTC P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) |
DTC P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0365 | No exhaust camshaft position sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic). |
|
| P0367 | The output voltage of the exhaust camshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic). |
|
| P0368 | The output voltage of the exhaust camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic). |
|
| Related DTCs | P0365: Exhaust camshaft position sensor verify pulse input P0367: Exhaust camshaft position sensor range check (low voltage) P0368: Exhaust camshaft position sensor range check (high voltage) |
| Required Sensors/Components (Main) | Exhaust camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds: P0365 4 seconds: P0367, P0368 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Engine speed | 600 rpm or higher |
| Exhaust camshaft position sensor range check fail (P0367, P0368) | Not detected |
| Ignition switch | ON |
| Starter | Off |
| Battery voltage | 8 V or higher |
| Exhaust camshaft position sensor voltage | 0.3 to 4.7 V |
| All of the following conditions are met | - |
| Starter | Off |
| Ignition switch | ON |
| Time after ignition switch turned from off to ON | 2 seconds or more |
| Exhaust camshaft position sensor verify pulse input fail (P0365) | Not detected |
| Battery voltage | 8 V or higher |
| Exhaust camshaft position signal | No signal |
| Exhaust camshaft position sensor voltage | Less than 0.3 V |
| Exhaust camshaft position sensor voltage | Higher than 4.7 V |
| Exhaust camshaft position sensor voltage | 0.3 to 4.7 V |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR) |
![]() |
Disconnect the camshaft position sensor for exhaust camshaft connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E52-3 (VC2) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Camshaft Position Sensor for Exhaust Camshaft) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor for exhaust camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E52-1 (VVE+) - E26-81 (EV1+) | Always | Below 1 Ω |
| E52-2 (VVE-) - E26-112 (EV1-) | Always | Below 1 Ω |
| E52-1 (VVE+) or E26-81 (EV1+) - Body ground | Always | 10 kΩ or higher |
| E52-2 (VVE-) or E26-112 (EV1-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT) |
![]() |
Check the camshaft position sensor for exhaust camshaft installation.
|
| ||||
| OK | |
| 4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR) |
Check the timing rotor of the exhaust camshaft.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |

| *1 | Timing Mark | - | - |
Remove the cylinder head cover sub-assembly.
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) |
Replace the camshaft position sensor (for exhaust camshaft) (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0365, P0367 or P0368 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor for exhaust camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E52-3 (VC2) - E26-111 (VCE1) | Always | Below 1 Ω |
| E52-3 (VC2) or E26-111 (VCE1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||