Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly LH (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly LH (for driver door) has motor, regulator and ECU functions.

WIRING DIAGRAM


B281016E09


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  3. If a power window regulator motor assembly LH (for driver door) has been replaced with a new one, initialize the power window control system (Click here).
  4. When the ECU determines that the power window regulator motor assembly LH (for driver door) has a malfunction, DTC B2311 is stored.

1.READ VALUE USING TECHSTREAM (MAIN BODY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Communication D-Door Motor
    Connection status between power window regulator motor assembly LH (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -

    OK:
    On the Techstream screen, OK is displayed.



NG
GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) (Click here)
OK


2.READ VALUE USING TECHSTREAM (DRIVER DOOR WINDOW MOTOR)
  1. Enter the following menus: Body Electrical / D-Door Motor / Data List.

  1. Read the Data List according to the display on the Techstream.

    D-Door Motor (Power Window Regulator Motor Assembly LH (for Driver Door)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver door power window manual up switch signal / ON or OFF
    ON: Driver door power window manual up switch operated
    OFF: Driver door power window manual up switch not operated
    -
    D Door P/W Down SW
    Driver door power window manual down switch signal / ON or OFF
    ON: Driver door power window manual down switch operated
    OFF: Driver door power window manual down switch not operated
    -

    OK:
    On the Techstream screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (DRIVER DOOR WINDOW MOTOR)
  1. Enter the following menus: Body Electrical / D-Door Motor / Active Test.

  1. Perform the Active Test according to the display on the Techstream.

    D-Door Motor (Power Window Regulator Motor Assembly LH (for Driver Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    OK:
    Driver door power window operates normally.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR DRIVER DOOR) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR LH (FOR DRIVER DOOR) - BATTERY AND BODY GROUND)
  1. Disconnect the power window regulator motor assembly LH (for driver door) connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K9-2 (B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K9-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)
  1. Disconnect the power window regulator master switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K11-8 (U) - K9-10 (UP1)
    Always
    Below 1 Ω
    K11-5 (D) - K9-7 (DWN1)
    Always
    Below 1 Ω
    K11-8 (U) - Body ground
    Always
    10 kΩ or higher
    K11-5 (D) - Body ground
    Always
    10 kΩ or higher
    K11-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B164359E79
  1. Remove the power window regulator master switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (U) - 1 (E)
    Manual UP
    Below 1 Ω
    5 (D) - 1 (E)
    Manual DOWN
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR DRIVER DOOR) (Click here)