Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.
      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape elasticity increases.

  1. Before installation

    1. Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

      NOTICE:
      Do not bend the tape or leave it in high temperature places.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

    NOTICE:
    1. Position the tape accurately to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit any more after being removed.




    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.


      B200106E02


      Text in Illustration 
      *A
      Pressing Forward
      *B
      Pulling
      *1
      Non-padded Side
      *2
      Padded Side
      *3
      Squeegee
      *4
      Black Out Tape
      *5
      Release Paper
      -
      -
      *a
      Side View
      -
      -
      Reference Measurement 
      Area
      Measurement
      A
      10 to 20 mm (0.393 to 0.787 in.)
      B
      30 to 70 mm/sec. (1.18 to 2.76 in./sec.)
      C
      40 to 50° (for pressing forward)
      D
      30 to 45° (for pulling)

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.

      HINT:
      1. Either angle of the squeegee (pressing forward or pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)



      B147253E09
    1. If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
      Text in Illustration 
      *1
      Squeegee
      *2
      Hem
      *a
      First
      *b
      Second
      *c
      Third

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

  1. Key points for installation of the tape (how to use a squeegee and installation procedure for corners)

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.

  1. Check after installation

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

      NOTICE:
      Do not reuse the tape.



3. INSTALL FRONT DOOR LOWER OUTSIDE STRIPE


  1. Refer to the illustration to position the front door lower outside stripe.


    B280087E01


    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Edge of Curved Surface
    *b
    Square
    *c
    Round
    -
    -
    Standard Measurement 
    Dimension
    Measurement
    A
    1.5 mm (0.0591 in.)
    B
    1.0 mm (0.0394 in.)

  1. Remove the release paper and apply the stripe.



4. INSTALL FRONT DOOR STRIPE


  1. Refer to the illustration to position a new front door stripe.


    B280088E01


    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Edge of Curved Surface
    *b
    Square
    *c
    Round
    -
    -
    Standard Measurement 
    Dimension
    Measurement
    A
    1.5 mm (0.0591 in.)
    B
    1.0 mm (0.0394 in.)

  1. Remove the release paper and apply the stripe.



5. INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING


    B280099
  1. Engage the claw and guide of the front door upper window frame moulding to the door frame.

  1. Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 7 new rivets.

    HINT:
    If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

    NOTICE:

    1. B125583E09
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
      Text in Illustration 
      *1
      Riveter
      *2
      Mandrel
      *a
      Incorrect

    2. B125584E10
      Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.
      Text in Illustration 
      *1
      Riveter
      *a
      Incorrect

    3. B125585E12
      Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.
      Text in Illustration 
      *1
      Riveter
      *a
      Incorrect



6. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:
When installing a new front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or front door rear window frame moulding excessively.

  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



    B280096E01
  1. Install a new front door rear window frame moulding.
    Text in Illustration 
    *1
    Double-sided Tape
    *2
    Caulking Sponge

    1. Using a heat light, heat the vehicle body and front door rear window frame moulding.

    2. Remove the release paper from the face of the front door rear window frame moulding.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Install the front door rear window frame moulding with the clip.



7. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY


    B280068
  1. Engage the 6 claws to install the front door belt moulding assembly.



8. INSTALL DOOR DUST PROOF SEAL


    B280379
  1. Install door dust proof seal.



9. INSTALL FRONT DOOR PANEL CUSHION


    B280378
  1. Engage the 2 claws to install 2 new front door panel cushions.



10. INSTALL FRONT DOOR NO. 2 WEATHERSTRIP


    B280377
  1. Engage the 8 clips to install the front door No. 2 weatherstrip.



11. INSTALL DOOR FRAME GARNISH


    B277197
  1. Engage the clip to install a new door frame garnish.



12. INSTALL FRONT DOOR WEATHERSTRIP


    B280376
  1. Engage the 19 clips and install the front door weatherstrip.



13. INSTALL FRONT DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the front door check assembly.

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B280375E01
  1. Install the front door check assembly with the 3 bolts.

    Torque:
    Bolt (A):
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    Bolt (B):
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



14. INSTALL FRONT DOOR LOCK OPEN ROD


    B280373E01
  1. Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.



15. INSTALL FRONT DOOR WIRE (w/ Smart Key System)


    B280372
  1. Engage the 3 clamps to install the front door wire.



16. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.



    B280371E01
  1. Engage the claw.
    Text in Illustration 
    *1
    Door Handle Nut
    *a
    Outside
    *b
    Inside

  1. Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw and door handle nut.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



  1. w/ Smart Key System:



      B280369
    1. Engage the 3 clamps.

    2. Connect the connector.



17. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280368
  1. Install the front door inside locking cable assembly.



    B280366
  1. Engage the 3 claws.



18. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280365
  1. Install the front door lock remote control cable assembly.



19. INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
  1. When reusing the removed front door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock with motor assembly.

  1. Apply MP grease to the sliding parts of the front door lock with motor assembly.



  1. When reusing the front door lock with motor assembly:



      B280363
    1. Install a new door lock wiring harness seal to the front door lock with motor assembly.



    B280362E01
  1. Insert the front door lock open rod to the front door lock with motor assembly.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

  1. Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



20. INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD


    B280360
  1. Engage the 2 claws to install the front door rear outside handle pad.



21. INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD


    B280359
  1. Engage the 3 claws to install the front door front outside handle pad.



22. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B280358
  1. Insert the front end of the front door outside handle assembly into the front door outside handle frame.

  1. Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.



  1. w/ Smart Key System:



      B288532
    1. Connect the connector.

    2. Engage the 2 claws.



23. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B280354
  1. Engage the 2 guides and claw, and install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.



24. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


  1. w/o Front Door Lock Cylinder:



      B280355
    1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

      Torque:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    2. B280630
    3. Install the hole plug.

  1. w/ Front Door Lock Cylinder:

    HINT:
    Use the same procedures for the front passenger side and the driver side.



25. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B280352
  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B280351
  1. Install the hole plug.



26. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Front Passenger Side)
  1. w/ Front Door Lock Cylinder:

    HINT:
    Use the same procedures for the front passenger side and the driver side.



27. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B280350
  1. Engage the guide as shown in the illustration.

  1. Install the front door rear lower frame sub-assembly with the 2 bolts.



28. INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    B280348
  1. Engage the guide as shown in the illustration.

  1. Install the front door front lower frame sub-assembly with the 2 bolts.



29. INSTALL FRONT DOOR GLASS RUN


    B280345
  1. Install the front door glass run.



30. INSTALL NO. 2 FRONT DOOR STIFFENER CUSHION
  1. Clean the front door panel sub-assembly.



    B280346E01
  1. Engage the 2 guides.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Install a new No. 2 front door stiffener cushion with the 2 bolts.



31. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor.



    B280344
  1. Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



32. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator assembly.

  1. Install the temporary bolt to the front door window regulator assembly.



    B280343E02
  1. Temporarily install the front door window regulator assembly.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



33. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the power window regulator master switch assembly.



    B280341E01
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.



    B280340
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B277200
  1. Install the grommet.



34. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the front door panel.



    B277199E01
  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
    Text in Illustration 
    *1
    Reference Point

  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Engage the 5 clamps.

  1. Install the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect each connector.



35. INSTALL DOOR SIDE AIRBAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



  1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296255E01


    Text in Illustration 
    *a
    Incorrect
    *b
    Correct

  1. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the body hole.
    4. Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. Connect the connector to the door side airbag sensor.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.




    1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).


      H043305E12


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Connection is Completed
      -
      -

      HINT:
      When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

  1. Check that there is no looseness in the installation parts of the door side airbag sensor.



36. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY
  1. Engage the claw to temporarily install the outer rear view mirror assembly.

  1. Install the outer rear view mirror assembly with the 3 bolts.

    Torque:
    11 N*m{ 107 kgf*cm , 8 ft.*lbf }

  1. Connect the connector.



37. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
  1. Engage the 2 claws to the vehicle body to temporarily install the front No. 1 speaker assembly.



    E226774E01
  1. Install the front No. 1 speaker assembly with the 4 screws.
     
    *A
    LH Side
    *B
    RH Side

    NOTICE:
    Do not touch the speaker cone.

    HINT:
    Install the screws in the order shown in the illustration.

  1. Connect the connector.



38. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    B277196
  1. Install the front door inner glass weatherstrip.



39. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B277194
  1. Engage the 2 claws and guide, and install the front door inside handle sub-assembly to the front door trim board sub-assembly.



40. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B277193E01
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly



    B277191E01
  1. Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss



    B277189
  1. Engage the 10 clips and install to front door trim board sub-assembly.

  1. Install the 3 screws.

  1. If protective tape has been applied, remove it.



41. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.



    E226715E01
  1. Engage the claw to install the courtesy light assembly.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



42. INSTALL FRONT ARMREST ASSEMBLY


    B277188
  1. Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.



43. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
  1. Connect each connector.



    B277184
  1. Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.



44. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect each connector.



    B277186
  1. Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.



45. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    B277182
  1. Engage the 3 clips to install the front door lower frame bracket garnish.



46. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B277181
  1. Engage the 3 claws to install the front door inside handle bezel plug.



47. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



48. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)
(Click here)


49. INSPECT POWER WINDOW OPERATION
(Click here)


50. INSPECT SRS WARNING LIGHT
for Separate Type Yaw Rate Sensor: (Click here)
for Built-in Type Yaw Rate Sensor: (Click here)