AUDIO AND VISUAL SYSTEM (for Radio and Display Type without Intuitive Parking Assist System) > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch assembly. | A |
| Illumination comes on for all components except radio and display receiver assembly. | B |
| Illumination comes on only for steering pad switch assembly. | C |
| No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL) |
Disconnect the spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I28-13 (IL+2) - Body ground | Light control switch in the tail or head position | 11 to 14 V |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector (for 3 Spoke, w/o Voice Switch of Steering Pad Switch Assembly).
Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

Disconnect the steering pad switch assembly connector (for 3 Spoke, w/ Voice Switch of Steering Pad Switch Assembly).
Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

Disconnect the steering pad switch assembly connector (for 4 Spoke, w/o Voice Switch of Steering Pad Switch Assembly).
Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

Disconnect the steering pad switch assembly connector (for 4 Spoke, w/ Voice Switch of Steering Pad Switch Assembly).
Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

Check if the illumination for the steering pad switch assembly comes on.
Proceed to the next step based on the check result.
| Result | Proceed to |
| OK | A |
| NG (for 3 Spoke) | B |
| NG (for 4 Spoke) | C |
| *A | for 3 Spoke | *B | for 4 Spoke |
| *a | Component without harness connected (Steering Pad Switch Assembly) | - | - |
|
| ||||
|
| ||||
| A | |
| 4.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the steering pad switch assembly connector.
Disconnect the spiral cable sub-assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-5 (IL+2) - I28-13 (IL+2) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-3 (-DP) - I28-11 (-DP) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-5 (IL+2) - I28-13 (IL+2) | Always | Below 3 Ω |
| z3-3 (-DP) - I28-11 (-DP) | Always | Below 3 Ω |
| *a | Component without harness connected (Spiral Cable Sub-assembly) |
| *b | Steering Pad Switch Assembly Side |
| *c | Vehicle Side |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL) |
Disconnect the radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I152-10 (ILL+) - Body ground | Light control switch in the tail or head position | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| I134-2 (ILL+) - Body ground | Light control switch in the tail or head position | 11 to 14 V |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY) |
Disconnect the radio and display receiver assembly connector.
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I153-5 (ILL-) - I18-4 (ILL-) | Always | Below 1 Ω |
| I153-5 (ILL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I134-12 (ILL-) - I18-4 (ILL-) | Always | Below 1 Ω |
| I134-12 (ILL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||