NAVIGATION SYSTEM (for Radio and Display Type) > Steering Pad Switch Circuit |

| 1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL) |
Disconnect the radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-21 (SW1) - I155-23 (SWG) | No switch pushed | 95 to 105 kΩ |
| Up switch pushed | Below 2.5 Ω | |
| Down switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| I155-22 (SW2) - I155-23 (SWG) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 313 to 345 Ω | |
| Off hook switch pushed | 950 to 1050 Ω | |
| Voice switch pushed | 2955 to 3265 Ω | |
| I155-24 (SW3) - I155-23 (SWG) | No switch pushed | 95 to 105 kΩ |
| Enter switch pushed | Below 2.5 Ω | |
| Back switch pushed | 313 to 345 Ω | |
| Right switch pushed | 950 to 1050 Ω | |
| Left switch pushed | 2955 to 3265 Ω |
|
| ||||
| OK | ||
| ||
| 2.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector (for 3 Spoke).

Disconnect the steering pad switch assembly connector (for 4 Spoke).

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-11 (AU1) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Up switch pushed | Below 2.5 Ω | |
| Down switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| z3-10 (AU2) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 313 to 345 Ω | |
| Off hook switch pushed | 950 to 1050 Ω | |
| Voice switch pushed | 2955 to 3265 Ω | |
| z3-9 (AU3) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Enter switch pushed | Below 2.5 Ω | |
| Back switch pushed | 313 to 345 Ω | |
| Right switch pushed | 950 to 1050 Ω | |
| Left switch pushed | 2955 to 3265 Ω |
Proceed to the next step based on the check result.
| Result | Proceed to |
| OK | A |
| NG (for 3 Spoke) | B |
| NG (for 4 Spoke) | C |
| *A | for 3 Spoke | *B | for 4 Spoke |
| *a | Component without harness connected (Steering Pad Switch Assembly) | *b | Volume+ |
| *c | Volume- | *d | Back |
| *e | MODE/HOLD | *f | Up |
| *g | Down | *h | Left |
| *i | Right | *j | Enter |
| *k | Off hook | *l | On hook |
| *m | Voice | - | - |
|
| ||||
|
| ||||
| A | |
| 3.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the steering pad switch assembly connector.
Disconnect the spiral cable sub-assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-8 (EAU) - I28-3 (EAU) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-11 (AU1) - I28-6 (AU1) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-10 (AU2) - I28-5 (AU2) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-9 (AU3) - I28-4 (AU3) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-8 (EAU) - I28-3 (EAU) | Always | Below 3 Ω |
| z3-11 (AU1) - I28-6 (AU1) | Always | Below 3 Ω |
| z3-10 (AU2) - I28-5 (AU2) | Always | Below 3 Ω |
| z3-9 (AU3) - I28-4 (AU3) | Always | Below 3 Ω |
| *a | Component without harness connected (Spiral Cable Sub-assembly) |
| *b | Steering Pad Switch Assembly Side |
| *c | Vehicle Side |
|
| ||||
| OK | ||
| ||