DTC P0500 Vehicle Speed Sensor "A" |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0500 | While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (1 trip detection logic). |
|
| Related DTCs | P0500: Vehicle speed sensor verify pulse input |
| Required Sensors/Components (Main) | Vehicle speed sensor Combination meter Skid control ECU |
| Required Sensors/Components (Related) | Park/neutral position switch Engine coolant temperature sensor Crankshaft position sensor Throttle position sensor Mass air flow meter sub-assembly |
| Frequency of Operation | Continuous |
| Duration | 2 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | Off |
| Time after ignition switch off to ON | 3 seconds or more |
| Engine | Running |
| Transmission counter gear revolution | 300 rpm or higher |
| Lost communication with TCM (U0101) | Not detected |
| Either of the following conditions is met | 1 or 2 |
| 1. All of the following conditions are met | - |
| Engine coolant temperature | 20°C (68°F) or higher |
| Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) | Not detected |
| Time after park/neutral position switch on to off | 2 seconds or more |
| 2. All of the following conditions are met | - |
| Either of the following conditions is met | (a) or (b) |
| (a) Engine coolant temperature | Less than 20°C (68°F) |
| (b) Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) | Detected |
| Time after park/neutral position switch on to off | 30 seconds or more |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | Off |
| Time after ignition switch off to ON | 3 seconds or more |
| Engine | Running |
| Transmission counter gear revolution | 300 rpm or higher |
| Either of the following conditions is met | 1 or 2 |
| 1. All of the following conditions are met | - |
| Engine coolant temperature | 20°C (68°F) or higher |
| Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) | Not detected |
| Time after park/neutral position switch on to off | 2 seconds or more |
| 2. All of the following conditions are met | - |
| Either of the following conditions is met | (a) or (b) |
| (a) Engine coolant temperature | Less than 20°C (68°F) |
| (b) Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) | Detected |
| Time after park/neutral position switch on to off | 30 seconds or more |
| Vehicle speed sensor signal | No signal |
| Sensor signal | No signal |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (VEHICLE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the Techstream.
| Result | Proceed to |
| Values displayed on Techstream and speedometer display not equal | A |
| Values displayed on Techstream and speedometer display equal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM) |
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-9 (+S) - A25-57 (SPD) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK COMBINATION METER SYSTEM |
Check the circuits that send vehicle speed signals to this system in the combination meter system (Click here).
| NEXT | |
| 4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
| NEXT | ||
| ||