Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Key-off Operation Function Operates even if Operating Conditions are not Satisfied

for Preparation Click here


DESCRIPTION

  1. When the front doors are closed, each power window regulator motor assembly can control its power window operation for approximately 43 seconds after the ignition switch is turned from ON to off by receiving operation permission signals from the main body ECU (multiplex network body ECU).
  2. However, when approximately 43 seconds have elapsed, or the driver door or front passenger door is opened within approximately 43 seconds of the ignition switch being turned off, the power window regulator motor assembly stops operating.
  3. During an auto operation, when 43 seconds have passed and key-off operation is prohibited, the window operation stops immediately.

INSPECTION PROCEDURE

NOTICE:
The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

1.CHECK MANUAL UP / DOWN FUNCTION
  1. Check that the manual up and down functions using the power window regulator master switch assembly and power window regulator switch assembly can operate all the power windows (Click here).

    OK:
    Manual up and down functions are normal.



NG
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) (Click here)
OK


2.CHECK REMOTE UP / DOWN FUNCTION
  1. Check that the remote up and down functions using the power window regulator master switch assembly can operate all the power windows (Click here).

    OK:
    Remote up and down functions are normal.



NG
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) (Click here)
OK


3.CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
  1. Check the power window operation function after the ignition switch is turned off.

    Result:

    Result
    Proceed to
    When power window can still be operated even after opening driver door or front passenger door within approximately 43 seconds of ignition switch being turned off
    A
    When power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for All Doors)
    B
    When power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for Driver Door)
    C
    When power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (Front Passenger Door, Rear LH Door or Rear RH Door)
    D



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

C
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR DRIVER DOOR) (Click here)

D
Go to step 5
A


4.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Courtesy
    Front door courtesy light switch RH / ON or OFF
    ON: Front door RH closed
    OFF: Front door RH open
    -
    FL Door Courtesy
    Front door courtesy light switch LH / ON or OFF
    ON: Front door LH closed
    OFF: Front door LH open
    -

    OK:
    On the Techstream screen, ON or OFF is displayed accordingly.



NG
GO TO LIGHTING SYSTEM (Proceed to Front Door Courtesy Switch Circuit) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Replace the main body ECU (multiplex network body ECU) (Click here).


NEXT


6.CHECK POWER WINDOW CONTROL SYSTEM
  1. Check the power window operation function after the ignition switch is turned off.

    OK:
    The power window control system operates normally.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)