Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B15C2    Speed Signal Malfunction

for Preparation Click here


DESCRIPTION

The navigation ECU sub-assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.
The navigation ECU sub-assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.
  2. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.


DTC No.
DTC Detection Condition
Trouble Area
B15C2
A difference between the GPS speed and SPD pulse is detected.
  1. Navigation ECU sub-assembly
  2. Combination meter assembly
  3. Harness or connector
  4. Junction connector

WIRING DIAGRAM


for 2GR-FE

E224310E01


for 2AR-FE

E224311E01


INSPECTION PROCEDURE

NOTICE:
After replacing the navigation ECU sub-assembly of vehicles subscribed to pay-type satellite radio broadcasts, registration of the XM radio ID is necessary.

1.CHECK VEHICLE SENSOR (OPERATION CHECK)


    E176549
  1. Enter the "Vehicle Sensors" screen. Refer to Check GPS & Vehicle Sensors in Operation Check (Click here).

  1. While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

    HINT:
    The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

    OK:
    Vehicle speed displayed on the "Vehicle Sensors" screen is almost the same as the actual vehicle speed measured using the Techstream (Click here).



NG
Go to step 2
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)  

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)


    E204779E06
  1. Check the output waveform.

    1. Remove the combination meter assembly with the connector(s) still connected.

    2. Connect an oscilloscope to terminal I18-9 (+S) and body ground.

    3. Turn the ignition switch to ON.

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Measurement terminal
      I18-9 (+S) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

      Text in Illustration 
      *a
      Component with harness connected
      (Combination Meter Assembly)



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-17 (SPD) - I18-9 (+S)
    Always
    Below 1 Ω



NG
Go to step 4
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - JUNCTION CONNECTOR)
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-17 (SPD) - I124-17
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)