Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A240424E09

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM


A255262E05


A255263E05


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

    OK:
    MIL lights up.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Check the communication between the Techstream and ECM.

    Result 
    Result
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3.CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle with motor body assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



B
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
A


4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
A


5.CHECK MIL (CANISTER PUMP MODULE)
  1. Disconnect the canister pump module connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE CANISTER PUMP MODULE (Click here)
A


6.CHECK MIL (INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE))
  1. Disconnect the intake air control valve actuator (for tumble control valve) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE) (Click here)
A


7.CHECK MIL (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)
  1. Disconnect the camshaft position sensor (for intake camshaft) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) (Click here)
A


8.CHECK MIL (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)
  1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) (Click here)
A


9.CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle with motor body assembly connector.

  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Disconnect the canister pump module connector.

  1. Disconnect the intake air control valve actuator (for tumble control valve) connector.

  1. Disconnect the camshaft position sensor (for intake camshaft) connector.

  1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E26-125 (VCTA) - Body ground
    Always
    10 kΩ or higher
    A25-53 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A25-56 (VCP2) - Body ground
    Always
    10 kΩ or higher
    E26-130 (VCIA) - Body ground
    Always
    10 kΩ or higher
    E26-34 (VCPP) - Body ground
    Always
    10 kΩ or higher
    E26-111 (VCE1) - Body ground
    Always
    10 kΩ or higher
    E26-113 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)