Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1497/97    BUS IC Communication Malfunction

for Preparation Click here


DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.

DTC No.
DTC Detection Condition
Trouble Area
B1497/97
Error or open in communication line
  1. Air conditioning harness assembly
  2. No. 1 air conditioning radiator damper servo sub-assembly
  3. No. 2 air conditioning radiator damper servo sub-assembly
  4. No. 1 blower damper servo sub-assembly
  5. Air conditioning amplifier assembly

WIRING DIAGRAM


E235674E09


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active test.

  1. Check the operation by referring to the table below.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse(D)
    No. 2 air conditioning radiator damper servo sub-assembly (air mix (for driver side)) pulse
    Min.: 0, Max.: 255
    Operates between 5 and 103 pulses
    Air Mix Servo Targ Pulse(P)
    No. 1 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) pulse
    Min.: 0, Max.: 255
    Operates between 7 and 105 pulses
    Air Outlet Servo Pulse (D)
    No. 1 air conditioning radiator damper servo sub-assembly (air outlet) pulse
    Min.: 0, Max.: 255
    Operates between 8 and 97 pulses
    Air Inlet Damper Targ Pulse
    No. 1 blower damper servo sub-assembly (air inlet) pulse
    Min.: 0, Max.: 255
    Operates between 7 and 28 pulses

    OK:
    Arm of the damper servo motor selected in the Active Test moves smoothly.

  1. According to the test result, proceed to the next step.

    Result:
    Result
    Proceed to
    One of the damper servo motors is malfunctioning
    A
    All of the damper servo motors are malfunctioning
    B



B
Go to step 7
A


2.SYSTEM CHECK
  1. According to the test result, proceed to the next step.

    Result:
    Result
    Proceed to
    Only the No. 2 air conditioning radiator damper servo sub-assembly (air mix (for driver side)) is malfunctioning
    A
    Only the No. 1 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) is malfunctioning
    B
    Only the No. 1 blower damper servo sub-assembly (air inlet) is malfunctioning
    C
    Only the No. 1 air conditioning radiator damper servo sub-assembly (air outlet) is malfunctioning
    D



B
Go to step 4

C
Go to step 5

D
Go to step 6
A


3.REPLACE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX (FOR DRIVER SIDE))
  1. Replace the No. 2 air conditioning radiator damper servo sub-assembly (air mix (for driver side)) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

4.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX (FOR FRONT PASSENGER SIDE))
  1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

5.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
  1. Replace the No. 1 blower damper servo sub-assembly (air inlet) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

6.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET)
  1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (air outlet) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

7.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

    HINT:
    Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 8
A

END 

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I77-21 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)