Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

DTC    B1497    Communication Malfunction (Bus Ic)

for Preparation Click here


DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.

DTC No.
DTC Detection Condition
Trouble Area
B1497
Error or open in communication line
  1. Air conditioning harness assembly
  2. No. 1 air conditioning radiator damper servo sub-assembly
  3. No. 1 blower damper servo sub-assembly
  4. Air conditioning amplifier assembly

WIRING DIAGRAM


E236248E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active test.

  1. Check the operation by referring to the table below.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse(D)
    No. 1 air conditioning radiator damper servo sub-assembly (air mix) pulse
    Min.: 0, Max.: 255
    Operates between 7 and 105 pulses
    Air Outlet Servo Pulse (D)
    No. 1 air conditioning radiator damper servo sub-assembly (air outlet) pulse
    Min.: 0, Max.: 255
    Operates between 8 and 97 pulses
    Air Inlet Damper Targ Pulse
    No. 1 blower damper servo sub-assembly (air inlet) pulse
    Min.: 0, Max.: 255
    Operates between 7 and 28 pulses

    OK:
    Arm of the damper servo motor selected in the Active Test moves smoothly.

  1. According to the test result, proceed to the next step.

    Result:
    Result
    Proceed to
    One of the damper servo motors is malfunctioning
    A
    All of the damper servo motors are malfunctioning
    B



B
Go to step 6
A


2.SYSTEM CHECK
  1. According to the test result, proceed to the next step.

    Result:
    Result
    Proceed to
    Only the No. 1 air conditioning radiator damper servo sub-assembly (air mix) is malfunctioning
    A
    Only the No. 1 blower damper servo sub-assembly (air inlet) is malfunctioning
    B
    Only the No. 1 air conditioning radiator damper servo sub-assembly (air outlet) is malfunctioning
    C



B
Go to step 4

C
Go to step 5
A


3.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX)
  1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497 is not output
    A
    DTC B1497 is output
    B



B
Go to step 6
A

END 

4.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
  1. Replace the No. 1 blower damper servo sub-assembly (air inlet) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497 is not output
    A
    DTC B1497 is output
    B



B
Go to step 6
A

END 

5.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET)
  1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (air outlet) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497 is not output
    A
    DTC B1497 is output
    B



B
Go to step 6
A

END 

6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

    HINT:
    Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497 is not output
    A
    DTC B1497 is output
    B



B
Go to step 7
A

END 

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I77-21 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)