Home › Engine / Hybrid System ยท 2GR-FE › FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(Click here)


2. DRAIN FUEL


3. REMOVE CENTER EXHAUST PIPE ASSEMBLY
(Click here)


4. REMOVE NO. 1 FLOOR UNDER COVER


    C239064
  1. Remove the 2 bolts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut (attached to under cover)

  1. Disengage the 3 nuts and 2 clips, and remove the No. 1 floor under cover.



5. REMOVE NO. 2 FLOOR UNDER COVER


    C239063
  1. Remove the 2 bolts and 2 clips.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut (attached to under cover)

  1. Disengage the 3 nuts and remove the No. 2 floor under cover.



6. DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY


    A254953E01
  1. Remove the nut and disconnect the No. 2 parking brake cable assembly.
    Text in Illustration 
    *1
    No. 2 Parking Brake Cable Assembly
    *2
    No. 3 Parking Brake Cable Assembly



7. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Remove the nut and disconnect the No. 3 parking brake cable assembly.



8. REMOVE REAR NO. 1 STABILIZER BAR BRACKET


    A254954
  1. Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets.



9. REMOVE NO. 1 FUEL TANK PROTECTOR


    A254955
  1. Remove the 3 clips and No. 1 fuel tank protector.



10. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A254956E01
  1. Pinch the tabs of the retainer to remove the lock claws and pull it down as shown in the illustration.
    Text in Illustration 
    *1
    Retainer
    *2
    Tab
    *3
    Fuel Tube Connector
    *4
    Fuel Pipe
    *5
    O-ring
    V100135
    Pinch
    V100136
    Pull

  1. Pull out the fuel tank main tube sub-assembly.

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected part of the fuel tube connector and fuel pipe before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.
    3. Only disconnect the fuel tube connector by hand.
    4. Do not forcibly bend, twist or turn the fuel tank main tube.
    5. Protect the disconnected part by covering it with plastic bags after disconnecting the fuel tube connector.
    6. If the fuel tube connector and fuel pipe are stuck, push and pull to release them.



11. DISCONNECT FUEL TANK BREATHER ELBOW TUBE SUB-ASSEMBLY


    A254957E01
  1. Pinch the tabs of the retainer to remove the lock claws and pull it down as shown in the illustration.
    Text in Illustration 
    *1
    Retainer
    *2
    Tab
    *3
    Fuel Tube Connector
    *4
    Fuel Pipe
    *5
    O-ring
    V100135
    Pinch
    V100136
    Pull

  1. Pull out the fuel tank breather elbow tube sub-assembly.

    NOTICE:
    1. Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.
    3. Only disconnect the fuel tube connector by hand.
    4. Do not forcibly bend, twist or turn the fuel tank breather tube.
    5. Protect the disconnected part by covering it with plastic bags after disconnecting the fuel tube connector.
    6. If the fuel tube connector and fuel pipe are stuck, push and pull to release them.



12. DISCONNECT FUEL TANK VENT HOSE


    A254958E01
  1. Pinch the tabs of the retainer to remove the lock claws and pull it down as shown in the illustration.
    Text in Illustration 
    *1
    Retainer
    *2
    Tab
    V100135
    Pinch
    V100136
    Pull

    NOTICE:
    1. Remove any dirt or foreign matter on the fuel tank vent hose connector before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tank vent hose connector has an O-ring that seals the pipe.
    3. Only disconnect the vent hose connector by hand.
    4. Do not forcibly bend, twist or turn the fuel tank vent hose.
    5. Protect the disconnected part by covering it with plastic bags after disconnecting the fuel tank vent hose.
    6. If the vent hose connector and charcoal canister are stuck, push and pull to release them.

  1. Pull out the fuel tank vent hose.



13. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    A254959E01
  1. Pull the tabs of the retainer to disengage the lock claws and pull out the fuel tank to filler pipe hose.
    Text in Illustration 
    *1
    Retainer
    V100135
    Pull
    V100136
    Pull Out

    NOTICE:
    1. Remove any dirt or foreign matter on the fuel tank to filler pipe hose connector before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tank to filler pipe hose connector has an O-ring that seals the fuel tank.
    3. Only disconnect the filler pipe hose connector by hand.
    4. Do not forcibly bend, twist or turn the fuel tank to filler pipe hose.
    5. Protect the disconnected part by covering it with plastic bags after disconnecting the fuel tank to filler pipe hose.
    6. If the fuel tank to filler pipe hose connector and fuel tank are stuck, push and pull to release them.



14. REMOVE FUEL TANK ASSEMBLY


    A254961
  1. Support the fuel tank using an engine lifter.



    A254960
  1. Remove the 4 bolts of the 2 fuel tank bands.

  1. Lower the engine lifter to remove the fuel tank.

    NOTICE:
    1. Slowly operate the engine lifter to lower the fuel tank.
    2. Do not drop the fuel tank.
    3. When removing the fuel tank, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.



15. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A254962
  1. Disconnect the No. 1 fuel tube clamp and remove the fuel tank main tube sub-assembly.



16. REMOVE FUEL TANK BREATHER ELBOW TUBE SUB-ASSEMBLY


    A254963
  1. Disconnect the No. 2 fuel tube clamp and remove the fuel tank breather elbow tube sub-assembly.



17. REMOVE FUEL TANK VENT HOSE


    A254964
  1. Disconnect the No. 2 fuel tube clamp and remove the fuel tank vent hose sub-assembly.



18. REMOVE NO. 1 FUEL TUBE CLAMP


    A254965E01
  1. Remove the No. 1 fuel tube clamp.
    Text in Illustration 
    *1
    No. 1 Fuel Tube Clamp
    *2
    No. 2 Fuel Tube Clamp



19. REMOVE NO. 2 FUEL TUBE CLAMP
  1. Remove the No. 2 fuel tube clamp.



20. REMOVE NO. 1 FUEL TANK CUSHION


    A254966
  1. Remove the 5 No. 1 fuel tank cushions.