Home › Engine / Hybrid System ยท 2AR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    U0101    Lost Communication with TCM

for Preparation Click here


DESCRIPTION

The Engine Control Module (ECM) communicates with the Transmission Control Module (TCM) through the Controller Area Network (CAN).
If there is a problem in this communication, the ECM stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
U0101
  1. Following conditions are met for 1.25 seconds (1 trip detection logic):
    1. Ignition switch ON
    2. Battery voltage is 10.5 V or higher
    3. No communication between ECM and TCM
ECM

MONITOR STRATEGY


Related DTCs
U0101: Verify communication
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1.25 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not stored
None
Both of the following conditions are met
-
Battery voltage
10.5 V or higher
Ignition switch
ON
Starter
Off

TYPICAL MALFUNCTION THRESHOLDS


Communication signal
Lost communication with TCM

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    1. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: U0101.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    1. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    1. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC U0101 is output
    A
    DTC U0101 and other DTCs are output
    B

    HINT:
    If any DTCs other than U0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A

REPLACE ECM (Click here)