Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1794    Open in Occupant Classification ECU Battery Positive Line

for Preparation Click here


DESCRIPTION

DTC B1794 is stored when a malfunction is detected in the occupant detection ECU battery positive line.

DTC No.
DTC Detections Conditions
Trouble Areas
B1794
  1. The occupant detection ECU receives an open circuit signal in the occupant detection ECU battery positive line.
  2. Occupant detection ECU malfunction
  1. Battery
  2. Wire harness
  3. Occupant detection ECU

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1794 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C239234E04


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK BATTERY VOLTAGE
  1. Measure the voltage of the battery.

    Standard Voltage:
    11 to 14 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2AR-FE)
    B
    NG (for 2GR-FE)
    C



B
INSPECT CHARGING SYSTEM AND BATTERY (Click here)

C
INSPECT CHARGING SYSTEM AND BATTERY (Click here)
A


2.CHECK WIRE HARNESS (SOURCE VOLTAGE)


    C239235E02
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the connector from the occupant detection ECU.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    d11-1 (+B) - Body ground
    Always
    11 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    d11-3 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Occupant Detection ECU)



NG
REPLACE WIRE HARNESS
OK


3.CHECK DTC
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Connect the connector to the occupant detection ECU.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in the occupant detection ECU (Click here).

  1. Clear the DTCs stored in the airbag sensor assembly (Click here for Separate Type Yaw Rate Sensor, Click here for Built-in Type Yaw Rate Sensor).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 10 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1794 is not output.

    HINT:
    Codes other than DTC B1794 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.



NG
Go to step 4
OK

USE SIMULATION METHOD TO CHECK (Click here)  

4.REPLACE OCCUPANT DETECTION ECU
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Replace the occupant detection ECU (Click here).

  1. Connect the cable to the negative (-) battery terminal.


NEXT


5.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).


NEXT

END