DTC B2782 Power Source Control ECU Malfunction |
| DTC No. | Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B2782 | Either condition is met (1-trip detection logic*):
|
| Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC) or on (IG) while carrying the key.) |
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
| The steering cannot be locked or unlocked. For this reason, the engine cannot be started. | Prohibits the engine from being started (the engine does not crank). |
| DTC No. | Data List Item | Active Test Item |
| B2782 | Smart Key
| - |

| 1.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the I24 steering lock ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I24-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Steering Lock ECU (Steering Lock Actuator Assembly)) |
Reconnect the I24 steering lock ECU connector.
Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P.
![]() |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
| Tester Connection | I24-3 (IGE) - I24-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating |
| *a | Component with harness connected (Steering Lock ECU (Steering Lock Actuator Assembly)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
|
| ||||
| OK | |
| 2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD |
Clear the DTCs (Click here).
Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored in the Data List.
| NEXT | |
| 3.READ VALUE USING TECHSTREAM (POWER SUPPLY SHORT) |
Perform the DTC output confirmation operation.
Check if DTC B2782 is output (Click here).
Use the Data List to check if the steering lock control is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Power Supply Short | Record of malfunction of signal sent to steering lock motor (steering lock actuator assembly) from certification ECU (smart key ECU assembly) (short circuit) / OK or NG(Past) | OK: No record of malfunction (short circuit) NG(Past): Record of malfunction (short circuit) exists | This item records malfunctions in the circuit between the certification ECU (smart key ECU assembly) and steering lock motor (steering lock actuator assembly). |
| Result | Proceed to |
| A |
| B |
|
| ||||
| A | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the I24 steering lock ECU connector.
Disconnect the I78 certification ECU (smart key ECU assembly) connector.
Check for deformation and corrosion of the connector case and terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I24-3 (IGE) - I78-29 (SLR+) | Always | Below 1 Ω |
| I24-3 (IGE) - Body ground | Always | 10 kΩ or higher |
| I78-29 (SLR+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||