STEERING LOCK SYSTEM > Unable to Lock Steering Wheel |
| Problem Symptom | Data List Item | Active Test Item |
| Unable to lock steering wheel | Smart Key
Main Body
| - |

| 1.CHECK DTC (ALL) |
Using the Techstream, confirm the output of DTCs for all systems.
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (LOCK REQUEST RECEIVE) |
Use the Data List to check if the steering lock command is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Lock Request Receive | Reception state of steering lock request signal by certification ECU (smart key ECU assembly) / OK or NG
| OK: Within 10 seconds of opening any door with engine switch off and shift lever in P NG: Except above | If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
|
| ||||
| OK | |
| 3.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the I24 steering lock ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I24-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Steering Lock ECU (Steering Lock Actuator Assembly)) |
Reconnect the I24 steering lock ECU connector.
Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P.
![]() |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
| Tester Connection | I24-3 (IGE) - I24-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating |
| *a | Component with harness connected (Steering Lock ECU (Steering Lock Actuator Assembly)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the I24 steering lock ECU connector.
Disconnect the I78 certification ECU (smart key ECU assembly) connector.
Check for deformation and corrosion of the connector case and terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I24-3 (IGE) - I78-29 (SLR+) | Always | Below 1 Ω |
| I24-3 (IGE) - Body ground | Always | 10 kΩ or higher |
| I78-29 (SLR+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING TECHSTREAM (FL DOOR COURTESY) |
Using the Techstream, check the following main body ECU Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FL Door Courtesy | Front door courtesy light switch assembly LH / ON or OFF | ON: Front door LH closed OFF: Front door LH open | If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or a related part. |
|
| ||||
| OK | |
| 6.READ VALUE USING TECHSTREAM (L CODE CHECK) |
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | |
| 7.REPLACE STEERING LOCK ACTUATOR ASSEMBLY |
Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).
Perform the registration procedures (Click here).
Turn the engine switch on (IG).
Operate the steering wheel and check the steering condition.
|
| ||||
| OK | ||
| ||
| 8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one (Click here).
Perform the registration procedures (Click here).
Use the Data List to check if L code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
|
| ||||
| OK | ||
| ||