Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Interior Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:
  1. Personal Light*1
  2. Rear Interior Light
  3. Ignition Key Cylinder Light*2

HINT:
The light cut relay supplies power to the lights not controlled by the illuminated entry system. If all the lights that use power from the light cut relay do not turn on, check the light cut relay circuit first (Click here).

  1. *1: w/ Sliding Roof
  2. *2: w/o Smart Key System

WIRING DIAGRAM


E230652E01


E230653E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check that the lights operate.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Personal light*2 and rear interior light
    ON/OFF
    1. No. 1 room light assembly switch in DOOR position*1
    2. Interior light door switch is on*2

    1. *1: w/o Sliding Roof
    2. *2: w/ Sliding Roof

    OK:
    Each light fades in.


Result 
Result
Proceed to
OK
A
NG (w/o Sliding Roof)
B
NG (w/ Sliding Roof and w/o Smart Key System)
NG (w/ Sliding Roof and w/ Smart Key System)
C


B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Perform the check under the following conditions:
    1. No. 1 room light assembly switch in DOOR position*1
    2. Interior light door switch on*2

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3B-34 - Body ground*3
    Ignition switch off
    11 to 14 V
    3B-35 - Body ground
    Ignition switch off
    11 to 14 V

  1. *1: w/o Sliding Roof
  2. *2: w/ Sliding Roof
  3. *3: w/o Smart Key System


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173026E06


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-34 - MB-1 (ILE)*1
    Always
    Below 1 Ω
    3B-35 - MB-1 (ILE)
    Always
    Below 1 Ω

  1. *1: w/o Smart Key System


NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.INSPECT ROOF CONSOLE BOX ASSEMBLY
  1. Remove the roof console box assembly (Click here).

  1. Inspect the roof console box assembly (Click here).

    OK:
    Roof console box assembly is normal.



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Install the roof console box assembly (Click here).

  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Perform the check under the following conditions:
    1. Interior light door switch on

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3B-35 - Body ground
    Ignition switch off
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173026E06


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-35 - MB-1 (ILE)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)