Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER

REAR SUSPENSION MEMBER > INSTALLATION

for Preparation Click here



1. INSTALL HOLE PLUG
  1. Install the 4 hole plugs to the rear suspension member sub-assembly.



2. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH


    C239614E01
  1. Temporarily install a new rear suspension member body mounting front cushion LH to the position shown in the illustration.
    Text in Illustration 
    *A
    Type A:
    *B
    Type B:
    V100135
    Front of the Vehicle



  1. Using SST and a press, install the rear suspension member body mounting front cushion LH to the rear suspension member sub-assembly.


    C239617E01

    SST
    09710-30012   (09710-04061)
    09950-60010   (09951-00650)
    09950-70010   (09951-07100)

    HINT:
    Slowly press in the rear suspension member body mounting front cushion LH.



    C239618
  1. While observing from the side, press in the rear suspension member body mounting front cushion LH until there is no clearance between the rear suspension member body mounting front cushion LH and the rear suspension member sub-assembly as shown in the illustration.

    NOTICE:
    Do not press the rear suspension member excessively, or it will easily deform.



3. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH


    C239615E01
  1. Temporarily install a new rear suspension member body mounting front cushion RH to the position shown in the illustration.
    Text in Illustration 
    *A
    Type A:
    *B
    Type B:
    V100135
    Front of the Vehicle



  1. Using SST and a press, install the rear suspension member body mounting front cushion RH to the rear suspension member sub-assembly.


    C239640E01

    SST
    09710-30012   (09710-04061)
    09950-60010   (09951-00650)
    09950-70010   (09951-07100)

    HINT:
    Slowly press in the rear suspension member body mounting front cushion RH.



    C239639
  1. While observing from the side, press in the rear suspension member body mounting front cushion RH until there is no clearance between the rear suspension member body mounting front cushion RH and the rear suspension member sub-assembly as shown in the illustration.

    NOTICE:
    Do not press the rear suspension member excessively, or it will easily deform.



4. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)


    C239616E01
  1. Temporarily install a new rear suspension member body mounting rear cushion (LH side) to the position shown in the illustration.
    Text in Illustration 
    *A
    Type A:
    *B
    Type B:
    V100135
    Front of the Vehicle



  1. Using SST and a press, install the rear suspension member body mounting rear cushion (LH side) to the rear suspension member sub-assembly.


    C239619E01

    SST
    09710-30012   (09710-04061)
    09950-60010   (09951-00650)
    09950-70010   (09951-07100)

    HINT:
    Slowly press in the rear suspension member body mounting rear cushion.



    C239637
  1. While observing from the side, press in the rear suspension member body mounting rear cushion (LH side) until there is no clearance between the rear suspension member body mounting rear cushion (LH side) and the rear suspension member sub-assembly as shown in the illustration.

    NOTICE:
    Do not press the rear suspension member excessively, or it will easily deform.



5. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

HINT:
Perform the same procedure as the LH side.



6. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    C239077
  1. Temporarily tighten the rear No. 1 suspension arm assembly (inner side) with the bolt.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Front of the Vehicle
    V100143
    Paint Mark

    HINT:
    Ensure that the paint mark faces the rear of the vehicle.



    C132503E07
  1. Set the rear No.1 suspension arm assembly in the position shown in the illustration, and fully tighten the bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }



7. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



8. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    C239075
  1. Temporarily tighten the rear No. 2 suspension arm assembly (inside) with the bolt.
    Text in Illustration 
    V100135
    Bolt
    V100143
    Paint Mark

    HINT:
    Ensure that the paint mark faces the rear of the vehicle.



9. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



10. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY
  1. w/ Member Cushion:

    1. Install 2 new differential support member cushions and 2 new differential support member upper stoppers to the rear suspension member sub-assembly.



    C239609E01
  1. Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools.
    Text in Illustration 
    *1
    Engine Lifter
    *2
    Attachment
    V100155
    Attachment Placement Location

    NOTICE:
    1. Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.
    2. Use the attachments to keep the rear suspension member sub-assembly level.

  1. Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and the vehicle body.

    NOTICE:
    When raising the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.



  1. Install the rear suspension member sub-assembly, rear suspension member lower stopper sub-assembly LH and rear suspension member lower stopper sub-assembly RH with the 4 nuts.


    C239636E01

    Torque:
    Nut A:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    Nut B:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



  1. Install the rear suspension member sub-assembly and 2 rear suspension member lower stoppers with the 2 bolts.


    C239635

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }

    NOTICE:
    Be sure to install the rear suspension member sub-assembly with the rear suspension member lower stoppers in the correct direction, as shown in the illustration.



11. INSTALL NO. 3 EXHAUST PIPE SUPPORT BRACKET
  1. Install the No. 3 exhaust pipe support bracket to the rear suspension member sub-assembly with the 2 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }



12. INSTALL JACK UP BRACKET (for 2GR-FE)
  1. Install the jack up bracket to the rear suspension member sub-assembly with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



13. INSTALL REAR SUSPENSION MEMBER DAMPER (w/ Dynamic Damper)


    C239623
  1. Install the rear suspension member damper to the rear suspension member sub-assembly with the 2 bolts.
    Text in Illustration 
    V100136
    Front of the Vehicle

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



14. CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
  1. Connect the rear No. 1 suspension arm assembly (outer side) to the rear axle carrier sub-assembly with the bolt and nut.

    NOTICE:
    When temporarily tightening the bolt, keep the nut from rotating.

    HINT:
    Insert the bolt from the front of the vehicle.



15. CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



16. CONNECT REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
  1. Connect the rear No. 2 suspension arm assembly (outer side) to the rear axle carrier sub-assembly with the bolt and nut.

    NOTICE:
    When temporarily tightening the bolt, keep the nut from rotating.

    HINT:
    Insert the bolt from the rear of the vehicle.



17. CONNECT REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



18. STABILIZE SUSPENSION


    C239098E01
  1. Jack up the rear axle carrier sub-assembly, placing a wooden block under it to avoid damage. Apply load to the suspension so that the installed bolt of the rear No. 1 suspension arm assembly (inner side) is horizontally aligned with the center of the rear axle hub.
    Text in Illustration 
    *1
    Wooden Block

    CAUTION:
    Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

    NOTICE:
    1. When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.
    2. Make sure to perform this operation with the vehicle kept as low as possible.



19. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    C239643
  1. Fully tighten the bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    NOTICE:
    Since a stopper nut is used, fully tighten the bolt.



20. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



21. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    C239642
  1. Fully tighten the 2 bolts.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }



22. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



23. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)
(Click here)


24. INSTALL REAR STABILIZER BAR


    C239620
  1. Install the rear stabilizer bar with the 4 bolts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Front of the Vehicle

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



25. CONNECT REAR STABILIZER LINK ASSEMBLY LH
  1. Connect the rear stabilizer link assembly LH to the rear stabilizer bar with nut.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.



26. CONNECT REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



27. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. for 2GR-FE: (Click here)
  2. for 2AR-FE: (Click here)


28. INSTALL NO. 2 FLOOR UNDER COVER (w/ Floor Under Cover)
  1. Install the No. 2 floor under cover with the 2 bolts, 3 nuts and 2 clips.

    Torque:
    Bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    Nut:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



29. INSTALL NO. 1 FLOOR UNDER COVER
  1. Install the No. 1 floor under cover with the 2 bolts, 3 nuts and 2 clips.

    Torque:
    Bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    Nut:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



30. INSTALL REAR WHEELS

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



31. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(Click here)


32. HEIGHT CONTROL SENSOR SIGNAL INITIALIZE (w/ Height Control Sensor)
(Click here)


33. ADJUST HEADLIGHT AIMING (w/ Height Control Sensor)
(Click here)