Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U1002    Lost Communication with Gateway Module (Network Gateway ECU)

for Preparation Click here


DESCRIPTION

  1. The network gateway ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 2.
  2. When the network gateway ECU receives a response signal from the ECUs connected to sub bus 2, the network gateway ECU recognizes and memorizes that the ECU is connected to sub bus 2. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to sub bus 2 when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 2, the network gateway ECU determines that a malfunction exists.

DTC No.
DTC Detection Condition
Trouble Area
U1002
Network gateway ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 2.
  1. Open or short in sub bus 2 main line or connector
  2. Open or short in sub bus 2 branch line or connector
  3. Network gateway ECU
  4. Blind spot monitor sensor LH
  5. Blind spot monitor sensor RH
  6. Open or short in CAN No. 3 junction connector
  7. Open or short in CAN No. 4 junction connector
  8. Open or short in CAN No. 5 junction connector

HINT:
This diagnosis procedure is for when DTC U1002 is output by the network gateway ECU (Techstream display: Gateway).


WIRING DIAGRAM


C240762E07


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 22 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more.
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK SUB BUS 2
  1. Disconnect the cable from the negative (-) battery terminal.



    C238893E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Result
    I81-13 (CA2H) - I81-12 (CA2L)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    Below 54 Ω:
    Short circuit between bus lines
    70 Ω or higher:
    Open circuit in a main bus line
    I81-13 (CA2H) - I81-4 (GND)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Below 200 Ω:
    CANH ground short
    I81-12 (CA2L) - I81-4 (GND)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Below 200 Ω:
    CANL ground short

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Result
    I81-13 (CA2H) - I81-2 (BATT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANH +B short
    I81-12 (CA2L) - I81-2 (BATT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANL +B short

    Text in Illustration 
    *a
    Component with harness connector
    (Network Gateway ECU)

    Result:
    Result
    Proceed to
    OK
    A
    Open circuit in CAN main bus line
    B
    Short circuit between bus lines
    C
    1. Ground short
    2. +B short
    D



B
Go to step 3

C
Go to step 7

D
Go to step 12
A


2.CHECK FOR DTC OUTPUT
  1. Clear the DTCs.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and recheck for DTCs.

    Result:
    Result
    Proceed to
    U1002 is output from network gateway ECU
    (Techstream display/Gateway)
    A
    Other DTC is output
    B



B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC
A

REPLACE NETWORK GATEWAY ECU (Click here)  

3.CHECK FOR OPEN IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)


    C238892E28
  1. Disconnect the network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I81-13 (CA2H) - I81-12 (CA2L)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Network Gateway ECU)



NG
Go to step 4
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

4.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 3 J/C)
  1. Reconnect the network gateway ECU connector.

  1. Disconnect the wire harness connector from the CAN No. 3 junction connector.



    C238890E22
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O30-10 (CANH) - O30-21 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    O30-11 (CANH) - O30-22 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN No. 3 Junction Connector)
    *b
    to CAN No. 4 Junction Connector
    *c
    to Network Gateway ECU

Result:
Result
Proceed to
OK
A
NG (to Network Gateway ECU main bus line)
B
NG (to CAN No. 4 junction connector main bus line)
C



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - NETWORK GATEWAY ECU)

C
Go to step 5
A

REPLACE CAN NO. 3 JUNCTION CONNECTOR 

5.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 4 J/C)
  1. Reconnect the wire harness connector to the CAN No. 3 junction connector.

  1. Disconnect the wire harness connector from the CAN No. 4 junction connector.



    C238890E23
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T15-9 (CANH) - T15-20 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    T15-11 (CANH) - T15-22 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to CAN No. 4 Junction Connector)
*b
to CAN No. 5 Junction Connector
*c
to CAN No. 3 Junction Connector

Result:
Result
Proceed to
OK
A
NG (to CAN No. 3 junction connector main bus line)
B
NG (to CAN No. 5 junction connector main bus line)
C



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

C
Go to step 6
A

REPLACE CAN NO. 4 JUNCTION CONNECTOR 

6.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 5 J/C)
  1. Reconnect the wire harness connector to the CAN No. 4 junction connector.

  1. Disconnect the instrument panel wire from the CAN No. 5 junction connector.



    C183982E23
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T16-3 (CANH) - T16-2 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 5 Junction Connector)
    *b
    to CAN No. 4 Junction Connector



NG
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 4 J/C - CAN NO. 5 J/C)
OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR 

7.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)


    C238892E28
  1. Disconnect the network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I81-13 (CA2H) - I81-12 (CA2L)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Network Gateway ECU)



NG
Go to step 8
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

8.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 3 J/C)
  1. Reconnect the network gateway ECU connector.

  1. Disconnect the wire harness connector from the CAN No. 3 junction connector.



    C238890E20
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O30-9 (CANH) - O30-20 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    O30-10 (CANH) - O30-21 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    O30-11 (CANH) - O30-22 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN No. 3 Junction Connector)
    *b
    to Blind Spot Monitor Sensor RH
    *c
    to CAN No. 4 Junction Connector
    *d
    to Network Gateway ECU

    Result:
    Result
    Proceed to
    OK
    A
    NG (to Network Gateway ECU main bus line)
    B
    NG (to CAN No. 4 junction connector main bus line)
    C
    NG (to Blind spot monitor sensor RH)
    D



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - NETWORK GATEWAY ECU)

C
Go to step 9

D
Go to step 11
A

REPLACE CAN NO. 3 JUNCTION CONNECTOR 

9.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 4 J/C)
  1. Reconnect the wire harness connector to the CAN No. 3 junction connector.

  1. Disconnect the wire harness connector from the CAN No. 4 junction connector.



    C238890E21
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T15-9 (CANH) - T15-20 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    T15-10 (CANH) - T15-21 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    T15-11 (CANH) - T15-22 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN No. 4 Junction Connector)
    *b
    to CAN No. 5 Junction Connector
    *c
    to Blind Spot Monitor Sensor LH
    *d
    to CAN No. 3 Junction Connector

Result:
Result
Proceed to
OK
A
NG (to CAN No. 3 junction connector main bus line)
B
NG (to CAN No. 5 junction connector main bus line)
C
NG (to Blind spot monitor sensor LH)
D



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

C
Go to step 10

D
Go to step 11
A

REPLACE CAN NO. 4 JUNCTION CONNECTOR 

10.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 5 J/C)
  1. Reconnect the wire harness connector to the CAN No. 4 junction connector.

  1. Disconnect the wire harness connector from the CAN No. 5 junction connector.



    C183982E23
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T16-3 (CANH) - T16-2 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 5 Junction Connector)
    *b
    to CAN No. 4 Junction Connector



NG
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 4 J/C - CAN NO. 5 J/C)
OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR 

11.CHECK FOR SHORT IN SUB BUS 2 LINES (ECUS)
  1. Reconnect all wire harness connectors (CAN J/C3 and CAN J/C4).

  1. Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short-circuited branch line is connected (Click here).



    C238893E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I81-13 (CA2H) - I81-12 (CA2L)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Component with harness connector
    (Network Gateway ECU)

    HINT:
    1. If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
    2. If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), repair or replace the short-circuited branch line or connector.



NG
REPAIR OR REPLACE CORRESPONDING ECU WIRE
OK

REPLACE CORRESPONDING ECU 

12.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 3 J/C)
  1. Disconnect the wire harness connector from the CAN No. 3 junction connector.



  1. Measure the resistance according to the value(s) in the table below.


    C240196E07


    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Purpose
    Connected to
    O30-9 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANH ground short
    Blind spot monitor sensor RH
    O30-20 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANL ground short
    O30-10 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANH ground short
    CAN No. 4 junction connector
    O30-21 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANL ground short
    O30-11 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANH ground short
    Network gateway ECU
    O30-22 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANL ground short
    O30-9 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    Blind spot monitor sensor RH
    O30-20 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANL +B short
    O30-10 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    CAN No. 4 junction connector
    O30-21 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANL +B short
    O30-11 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    Network gateway ECU
    O30-22 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANL +B short


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to CAN No. 3 Junction Connector)
    *b
    to Blind Spot Monitor Sensor RH
    *c
    to CAN No. 4 Junction Connector
    *d
    to Network Gateway ECU

    Result:
    Result
    Proceed to
    OK
    A
    NG (to Network Gateway ECU main bus line)
    B
    NG (to CAN No. 4 junction connector main bus line)
    C
    NG (to Blind spot monitor sensor RH)
    D

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

    Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



B
Go to step 13

C
Go to step 14

D
Go to step 16
A

REPLACE CAN NO. 3 JUNCTION CONNECTOR 

13.CHECK FOR SHORT IN SUB BUS 2 LINE (NETWORK GATEWAY ECU)
  1. Disconnect the network gateway ECU connector.



    C238892E29
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Purpose
    I81-13 (CA2H) - I81-4 (GND)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Below 200 Ω:
    CANH ground short
    I81-12 (CA2L) - I81-4 (GND)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Below 200 Ω:
    CANL ground short
    I81-13 (CA2H) - I81-2 (BATT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANH +B short
    I81-12 (CA2L) - I81-2 (BATT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANL +B short

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Network Gateway ECU)

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

    Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



NG
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - NETWORK GATEWAY ECU)
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

14.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 4 J/C)
  1. Disconnect the wire harness connector from the CAN No. 4 junction connector.



  1. Measure the resistance according to the value(s) in the table below.


    C240196E08


    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Purpose
    Connected to
    T15-9 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANH ground short
    CAN No. 5 junction connector
    T15-20 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANL ground short
    T15-10 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANH ground short
    Blind spot monitor sensor LH
    T15-21 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANL ground short
    T15-11 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANH ground short
    CAN No. 3 junction connector
    T15-22 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inspection for CANL ground short
    T15-9 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    CAN No. 5 junction connector
    T15-20 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANL +B short
    T15-10 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    Blind spot monitor sensor LH
    T15-21 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANL +B short
    T15-11 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANH +B short
    CAN No. 3 junction connector
    T15-22 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inspection for CANL +B short


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to CAN No. 4 Junction Connector)
    *b
    to CAN No. 5 Junction Connector
    *c
    to Blind Spot Monitor Sensor LH
    *d
    to CAN No. 3 Junction Connector

    Result:
    Result
    Proceed to
    OK
    A
    NG (to CAN No. 3 junction connector main bus line)
    B
    NG (to CAN No. 5 junction connector main bus line)
    C
    NG (to Blind spot monitor sensor LH)
    D

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

    Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

C
Go to step 15

D
Go to step 16
A

REPLACE CAN NO. 4 JUNCTION CONNECTOR 

15.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 5 J/C)
  1. Disconnect the wire harness connector from the CAN No. 5 junction connector.



    C231891E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Purpose
    T16-3 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Below 200 Ω:
    CANH ground short
    T16-2 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Below 200 Ω:
    CANL ground short
    T16-3 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANH +B short
    T16-2 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANL +B short

    Text in Illustration 
    *1
    DLC3
    *a
    Front view of wire harness connector
    (to CAN No. 5 Junction Connector)

    HINT:
    It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

    Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



NG
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 4 J/C - CAN NO. 5 J/C)
OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR 

16.CHECK SUB BUS 2 LINE (ECUS)
  1. Reconnect all wire harness connectors (CAN J/C3 and CAN J/C4).

  1. Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to B+ or shorted to GND is connected.



    C238893E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Purpose
    I81-13 (CA2H) - I81-4 (GND)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Below 200 Ω:
    CANH ground short
    I81-12 (CA2L) - I81-4 (GND)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Below 200 Ω:
    CANL ground short
    I81-13 (CA2H) - I81-2 (BATT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANH +B short
    I81-12 (CA2L) - I81-2 (BATT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Below 6 kΩ:
    CANL +B short

    Text in Illustration 
    *a
    Component with harness connector
    (Network Gateway ECU)

    HINT:
    1. It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
    2. If the resistance becomes abnormal when an ECU connector is reconnected, there may be a short in the ECU.
      Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



NG
REPAIR OR REPLACE CORRESPONDING ECU WIRE
OK

REPLACE CORRESPONDING ECU