Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Intuitive Parking Assist System)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Intuitive Parking Assist System) > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

  1. The navigation ECU sub-assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
  2. Using this circuit, the navigation ECU sub-assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the navigation ECU sub-assembly.

WIRING DIAGRAM


E227677E18


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the roof console box assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-4 (MACC) - S12-14 (MACC)
    Always
    Below 1 Ω
    I67-5 (MIN+) - S12-13 (MCO+)
    Always
    Below 1 Ω
    I67-19 (MIN-) - S12-12 (MCO-)
    Always
    Below 1 Ω
    I67-6 (SNS2) - S12-15 (SNS2)
    Always
    Below 1 Ω
    I67-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    I67-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    I67-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    I67-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    I67-6 (SNS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT NAVIGATION ECU SUB-ASSEMBLY
  1. Reconnect the navigation ECU sub-assembly connector.

  1. Reconnect the roof console box assembly (telephone microphone assembly) connector.



    E176671E56
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I67-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-18 (SGND) - Body ground
    Always
    Below 1 Ω
    I67-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation ECU Sub-assembly)



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK


3.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Disconnect the roof console box assembly (telephone microphone assembly) connector.



    E187117E20
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-15 (SNS2) - S12-12 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
OK


4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Reconnect the navigation ECU sub-assembly connector.



    E187122E18
  1. Reconnect the roof console box assembly (telephone microphone assembly) connector.

  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S12 roof console box assembly (telephone microphone assembly) connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output
    A
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output
    B

    Text in Illustration 
    *a
    Component with harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))



B
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)