Display Function
Symptom
| Suspected Area
| See page
|
Pressing power switch does not turn on system.
| Proceed to "Radio Receiver Power Source Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Black screen (No image appears on/audio screen.)
| Proceed to "Black Screen"
|
Click here
|
Proceed to "Check Software Error History" in Operation Check
|
Click here
|
Hard disk drive
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Display does not dim (does not change to night screen) with tail switch on.
| Proceed to "Display does not Dim when Light Control Switch is Turned ON"
|
Click here
|
Proceed to "Illumination Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Power does not turn off. (Screen remains on.)
| Proceed to "Radio Receiver Power Source Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Display panel does not open, tilt, or tilts improperly.
| Proceed to "Display Panel does not Open, Tilt or Tilts Improperly"
|
Click here
|
Proceed to "Radio Receiver Power Source Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Screen is distorted.
| Proceed to "Radio Receiver Power Source Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Screen flicker or color distortion.
| Proceed to "Screen Flicker or Color Distortion"
|
Click here
|
Proceed to "Radio Receiver Power Source Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Panel Switch and Touch Switch Function
Symptom
| Suspected Area
| See page
|
Illumination for panel switches does not come on with tail switch on.
| Proceed to "Illumination for Panel Switch does not Come on with Tail Switch ON"
|
Click here
|
Proceed to "Illumination Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Panel switches do not function.
| Proceed to "Panel Switches do not Function"
|
Click here
|
Proceed to "Radio Receiver Power Source Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Touch panel switch does not function.
| Proceed to "Touch Panel Switch does not Function"
|
Click here
|
Proceed to "Steering Pad Switch Circuit"
|
Click here
|
Proceed to "Radio Receiver Power Source Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Customize Startup Image or Screen Off Image Function
Symptom
| Suspected Area
| See page
|
Screen cannot be changed to UIC setting screen.
| Navigation ECU sub-assembly
|
Click here
|
Thumbnails for opening image setting or screen off image setting do not update when USB device is connected.
| Check that the USB device was not disconnected while transferring an image.
| -
|
Check that the screen was not changed to another function menu while transferring an image.
| -
|
Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Transfer button cannot be pressed.
| Check that a USB device is connected.
| -
|
Check that the USB device is not in use. (USB audio system is playing etc.)
| -
|
Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Image data in USB device cannot be displayed.
| Check that the designated folder name is used.
| -
|
Check that the file extension of the data is JPG or JPEG.
| -
|
Check that the file name is 32 characters or less and available language is used.
| -
|
Check that the image data size is 10 MB or less.
| -
|
Check that the file system of the USB device is FAT16 or FAT32.
| -
|
Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Set opening image or screen off image is not displayed.
| Check if it is the first start-up after disconnecting and reconnecting the +B terminal. (Reading from the HDD may be slow when the system is first starting-up.)
| -
|
Set the opening image or screen off image again.
| -
|
Navigation ECU sub-assembly
|
Click here
|
Stored image cannot be deleted.
| Navigation ECU sub-assembly
|
Click here
|
Message indicating that USB device cannot be accessed is displayed.
| Check that the USB device has not been disconnected while the audio and visual system is recognizing it.
| -
|
Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Thumbnail images for opening image or screen off image are not displayed on setting screen.
| Check if it is the first start-up after disconnecting and reconnecting the +B terminal. (Reading from the HDD may be slow when the system is first starting-up.)
| -
|
Set the opening image or screen off image again.
| -
|
Navigation ECU sub-assembly
|
Click here
|
Image cannot be set for opening image or screen off image on setting screen.
| Set the opening image or screen off image again.
| -
|
Navigation ECU sub-assembly
|
Click here
|
General Audio Function
Symptom
| Suspected Area
| See page
|
No sound can be heard from speakers.
| Proceed to "No Sound can be Heard from Speakers"
|
Click here
|
Proceed to "Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier"
|
Click here
|
Proceed to "Speaker circuit"
|
Click here
|
Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier"
|
Click here
|
Stereo component amplifier assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Abnormal noise occurs.
| Proceed to "Noise Occurs"
|
Click here
|
Stereo component amplifier assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Sound quality is bad in all modes. (Volume is too low.)
| Check that the ASL function is off.
| -
|
Proceed to "Poor Sound Quality in All Modes (Low Volume)"
|
Click here
|
Proceed to "Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier"
|
Click here
|
Proceed to "Speaker circuit"
|
Click here
|
Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier"
|
Click here
|
Stereo component amplifier assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
ASL does not function.
| Check that the ASL function is on.
| -
|
Proceed to "Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter"
|
Click here
|
Stereo component amplifier assembly
|
Click here
|
Voice guidance does not function.
| Proceed to "Voice Guidance does not Function"
|
Click here
|
Proceed to "Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier"
|
Click here
|
Proceed to "Speaker Circuit"
|
Click here
|
Proceed to "Voice Guidance Signal Circuit between Radio Receiver and Stereo Component Amplifier"
|
Click here
|
Stereo component amplifier assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Voice menu screen is not displayed. (Voice recognition function does not turn on.)
| Check if the voice recognition prompts function is "On".
| -
|
Proceed to "Panel Switches do not Function"
|
Click here
|
Proceed to "Steering Pad Switch Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
When voice recognition switch is pressed, a short beep is emitted but voice cannot be recognized properly.
| Proceed to "Voice is not Recognized"
|
Click here
|
Proceed to "Microphone Circuit between Microphone and Radio Receiver"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Customizable parameters cannot be changed. (Customizable parameters can be changed by using the Techstream.)
| Navigation ECU sub-assembly
|
Click here
|
Reverse signal does not change in vehicle signal check mode.
| Proceed to "Reverse Signal Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Parking brake switch signal does not change in vehicle signal check mode.
| Proceed to "Parking Brake Switch Circuit"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
AUX" is not displayed on system check mode screen.
| Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
CD or DVD Player Function
Symptom
| Suspected Area
| See page
|
Disc cannot be inserted/played or disc is ejected right after insertion.
| Proceed to "Check Optical Disc Error History" in Operation Check
|
Click here
|
Proceed to "Disc cannot be Inserted or is Ejected Right After Insertion"
|
Click here
|
Disc cannot be ejected.
| Proceed to "Check Optical Disc Error History" in Operation Check
|
Click here
|
Proceed to "Disc cannot be Ejected"
|
Click here
|
Sound quality is bad only when disc is played. (Volume is too low.)
| Proceed to "Check Optical Disc Error History" in Operation Check
|
Click here
|
Proceed to "Sound Quality is Bad Only when Disc is Played (Volume is Too Low)"
|
Click here
|
Disc sound skips.
| Proceed to "Check Optical Disc Error History" in Operation Check
|
Click here
|
Proceed to "CD/DVD Sound Skips"
|
Click here
|
While vehicle is stopped, DVD cannot be viewed even when parking brake is set. (Parking brake switch is on.)
| Proceed to "Parking Brake Switch Circuit"
|
Click here
|
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter"
|
Click here
|
Screen color is poor only when watching DVD.
| Change the color settings on the screen adjustment screen.
| -
|
Navigation ECU sub-assembly
|
Click here
|
"Bluetooth" Hands-free Function
Symptom
| Suspected Area
| See page
|
Bluetooth is inoperative.
| Proceed to "Microphone Circuit between Microphone and Radio Receiver"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Cellular phone registration failure.
| Proceed to "Cellular Phone Registration Failure, Phonebook Transfer Failure"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Cellular phone cannot make outgoing/incoming calls or call in a certain place.
| Proceed to "Cellular Phone cannot Make Outgoing/Incoming Calls"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Message that prompts to check the cellular phone is displayed.
| Proceed to "Cellular Phone cannot Make Outgoing/Incoming Calls"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Phonebook data cannot be transferred manually or automatically.
| Check the automatically download contact setting.
| -
|
When transferring phonebook data, OBEX authentication may be required. Enter "1234" into the "Bluetooth" phone.
| -
|
Proceed to "Cellular Phone Registration Failure, Phonebook Transfer Failure"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Volume of other caller's voice is not at an appropriate volume level, there is noise, sound quality is poor or other caller's voice cannot be heard.
| Proceed to "Check Hands-free Voice Quality and Volume Setting" in Operation Check
|
Click here
|
Proceed to "The Other Caller's Voice cannot be Heard, is too Quiet, or Distorted"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Stereo component amplifier assembly
|
Click here
|
Other caller cannot hear your voice at an appropriate volume level, there is noise or an echo, sound quality is poor or other caller cannot hear your voice.
| Proceed to "Check Hands-free Voice Quality and Volume Setting" in Operation Check
|
Click here
|
Proceed to "The Other Caller cannot Hear Your Voice, or Your Voice is too Quiet or Distorted"
|
Click here
|
Proceed to "Microphone Circuit between Microphone and Radio Receiver"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
"Bluetooth" Audio Function
Symptom
| Suspected Area
| See page
|
Portable player cannot be registered.
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Portable player cannot be connected manually/automatically.
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Proceed to "Portable Player cannot be Connected Manually/Automatically"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Cellular phone with portable audio function cannot be recognized as "Bluetooth" audio device even when connected using "Bluetooth".
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Proceed to "Portable Player cannot be Connected Manually/Automatically"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Sound of portable player cannot be heard from speakers, or sound is low.
| Proceed to "Sound of Portable Player cannot be Heard from Speakers or Sound is Low"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Portable player does not play even after "Bluetooth" audio mode is selected.
| Proceed to "Does not Play even after Bluetooth Audio Mode is Selected"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Portable player does not play.
| Proceed to "Does not Play even after Bluetooth Audio Mode is Selected"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Track information such as track number, track name, elapsed play time and playlist is not displayed.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on vehicle Device"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Operation switches for portable player such as play, pause, repeat, random and scan are not displayed.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on vehicle Device"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Battery condition of portable player is not displayed.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on vehicle Device"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
"Bluetooth" signal condition is not displayed.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on vehicle Device"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Portable player cannot pause, select file, fast forward, fast rewind, play at random or scan.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on vehicle Device"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Noise occurs or sound skips when portable player plays.
| Proceed to "Noise Occurs or Sound Skips when Portable Player Plays"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Registered device cannot be deleted.
| Proceed to "Registered Device cannot be Deleted"
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
USB Audio System Function
Symptom
| Suspected Area
| See page
|
USB audio system sound cannot be heard or sound quality is bad. (USB connector is used.)
| Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
USB device or "iPod" is not recognized.
| Proceed to "USB Audio System Recognition Play/Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Track information such as track, artist and album names are not displayed.
| Proceed to "USB Audio System Recognition Play/Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
USB device or "iPod" is recognized but cannot play nor play in a sorted order.
| Proceed to "USB Audio System Recognition Play/Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Album cover art cannot be displayed.
| Check that display cover art on the "iPod" settings screen is set to on.
| -
|
Check that a JPEG file is used for the cover art.
| -
|
"iPod" battery cannot be charged.
| Proceed to "USB Audio System Recognition Play/Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation ECU sub-assembly
|
Click here
|
Fuel Consumption Function
Symptom
| Suspected Area
| See page
|
"Fuel Consumption" icon is dimmed.
| Check if other icons or items displayed on screen have any problems.
| -
|
Navigation ECU sub-assembly
|
Click here
|
Graph is not displayed on "Trip Information" screen.
| Recheck with the engine running.
| -
|
Navigation ECU sub-assembly
|
Click here
|
Cruise range is not displayed on "Trip Information" screen.
| Turn ignition switch to ON and recheck.
| -
|
Navigation ECU sub-assembly
|
Click here
|
Graph is not updated on "Past record" screen even though "Clear" is selected.
| Turn ignition switch to ON and recheck.
| -
|
Navigation ECU sub-assembly
|
Click here
|
Graph is not displayed on "Past record" screen.
| Turn ignition switch to ON and recheck.
| -
|
Navigation ECU sub-assembly
|
Click here
|