Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U0233    Lost Communication with Blind Spot Monitor Master Module

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
U0233
No communication from the blind spot monitor sensor RH continues.
  1. Blind spot monitor sensor RH branch line or connector
  2. Power source circuit of blind spot monitor sensor RH
  3. Blind spot monitor sensor RH ground circuit
  4. Blind spot monitor sensor RH

HINT:
This diagnosis procedure is for when DTC U0233 is output by the network gateway ECU (Techstream display: Gateway).


WIRING DIAGRAM


C240761E08


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 22 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more.
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.RECONFIRM DTC OUTPUT
  1. Reconfirm DTCs.

    HINT:
    If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.

    Result:
    Result
    Proceed to
    U1002 is not output from network gateway ECU (Techstream display/Gateway)
    A
    U1002 is output from network gateway ECU (Techstream display/Gateway)
    B



B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC (Click here)
A


2.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR RH BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C240531E24
  1. Disconnect the blind spot monitor sensor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O28-8 (CA1P) - O28-4 (CA1N)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor RH)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH)
OK


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    C240531E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O28-1 (BRGD) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor RH)

  1. Connect the cable to the negative (-) battery terminal.



    C240531E26
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O28-5 (BRB) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor RH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

REPLACE BLIND SPOT MONITOR SENSOR RH (Click here)