INTAKE MANIFOLD > INSTALLATION |
| 1. INSTALL INTAKE MANIFOLD |
Set 2 new gaskets on each cylinder head sub-assembly.
Set the intake manifold on the cylinder head sub-assembly.
Install and tighten the 6 bolts and 4 nuts uniformly in several steps.
| 2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() |
Install 6 new injector vibration insulators to the intake manifold.
Place the fuel delivery pipe with the 6 fuel injectors in position on the intake manifold.
![]() |
Temporarily install the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.
![]() |
Tighten the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.
![]() |
Connect the 6 fuel injector connectors.
| 3. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push in the fuel tube connector onto the pipe until the fuel tube connector makes a "click" sound.
| *1 | No. 2 Fuel Pipe Clamp |
| *2 | Retainer |
| *3 | Fuel Tube Connector |
| *4 | O-ring |
| *5 | Fuel Pipe |
![]() | Push |
Install the No. 2 fuel pipe clamp.
| 4. INSTALL NO. 2 ENGINE MOUNTING STAY RH (for Intake Manifold Side) |
Install the No. 2 engine mounting stay RH with the bolt.
| 5. INSTALL NO. 2 ENGINE MOUNTING STAY RH (for Engine Mounting Stay Side) |
Install the No. 2 engine mounting stay RH with the bolt.
Tighten the 2 nuts.
| 6. INSTALL INTAKE AIR SURGE TANK ASSEMBLY |
| Oil Application Prohibited Bolt |
| Intake Air Surge Tank Assembly and Intake Manifold |
| No. 1 Surge Tank Stay and Intake Air Surge Tank Assembly |
| Throttle Body Bracket and Intake Air Surge Tank Assembly |
Install 3 new gaskets to the intake air surge tank assembly.
Temporarily install the intake air surge tank assembly with the 4 bolts and 2 nuts.
![]() |
Using a 5 mm hexagon socket wrench, in several steps, uniformly tighten the 4 bolts and 2 nuts in the order shown in the illustration.
Install the throttle body bracket and No. 1 surge tank stay with the 2 bolts.
Install the vacuum hose clamp with the bolt.
Connect the connector to the intake air control valve assembly.
Connect the 2 water by-pass hoses and fuel vapor feed hose.
Connect the connector and wire harness clamp to the throttle body assembly.
Connect the hose clamp and union to check valve hose.
Connect the ventilation hose.
| 7. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Connect the air cleaner cap sub-assembly to the throttle with motor body assembly with the hose clamp.
Install the air cleaner cap with hose to the air cleaner case with the 2 clamps.
Connect the wire harness clamp and mass air flow meter connector.
Connect the 3 hoses.
Connect the ventilation hose.
Connect the mass air flow meter connector and wire harness clamp.
| 8. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 9. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 11. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Close the 2 cylinder block drain cock plugs.
Loosen the air drain cock plug on the water inlet housing.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 12. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 13. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect the Techstream to the DLC3.
Turn the engine switch on (IG) and turn the Techstream on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, fuel pump control ECU, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the engine switch off.
Disconnect the Techstream from the DLC3.
| 14. INSTALL V-BANK COVER SUB-ASSEMBLY |
Fit the 3 retainers and install the V-bank cover sub-assembly.