Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B279A
The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high (1 trip detection logic*).
  1. Wire harness or connector (disconnection or break in wire harness is main cause)
  2. Certification ECU (smart key ECU assembly)
  3. ECM
Turn the engine switch on (IG) and wait 6 seconds.
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops)
Engine cannot be started

Related Data List and Active Test 
DTC Code
Data List and Active Test
B279A
-

WIRING DIAGRAM


B271007E12


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the certification ECU (smart key ECU assembly), refer to Registration (Click here).
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

HINT:
When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK DTC OUTPUT
  1. Turn the engine switch on (IG) and wait 10 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B

    HINT:
    If DTCs other than DTC B279A are output, troubleshoot those DTCs first.



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK CONNECTION OF CONNECTOR
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A25 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    A43-13 (EFIO) - A25-31 (IMI)
    Always
    Below 1 Ω
    A25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A43-13 (EFIO) - A25-28 (IMI)
    Always
    Below 1 Ω
    A25-28 (IMI) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-31 (IMI) - Body ground
    Always
    Below 1 V
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-28 (IMI) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one (Click here).


NEXT


6.REGISTER RECOGNITION CODES
  1. Register the recognition codes in the ECUs (Click here).


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID (Click here).


NEXT


8.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE)
    B
    NG (for 2AR-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)