COOLING FAN SYSTEM > Cooling Fan Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE ELECTRIC COOLING FAN) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Electric Cooling Fan.
Check the operation of the cooling fans while operating them using the Techstream.
| Techstream Operation | Specified Condition |
| ON | Cooling fans operating |
| OFF | Cooling fans stopped |
| Result | Proceed to |
| OK | A |
| NG (Cooling fans do not operate) | B |
| NG (Cooling fans do not stop) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO. 2 COOLING FAN MOTOR) |
Inspect the cooling fan motor and No. 2 cooling fan motor (Click here).
| Result | Proceed to |
| OK | A |
| NG (Cooling fan motor) | B |
| NG (No. 2 cooling fan motor) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE) |
![]() |
Disconnect the cooling fan ECU connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A10-3 (+B1) - A10-1 (E1) | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Cooling Fan ECU) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU) |
Disconnect the ECM connector.
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-5 (RFC) or A10-2 (SI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND) |
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A10-1 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.INSPECT RELAY (FAN RELAY) |
Inspect the FAN relay (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE) |
![]() |
Remove the FAN relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (FAN relay) - Body ground | Always | 11 to 14 V |
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | FAN Relay |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY) |
Remove the FAN relay from the engine room relay block and junction block assembly.
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A10-3 (+B1) - 5 (FAN relay) | Always | Below 1 Ω |
| A10-3 (+B1) or 5 (FAN relay) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND) |
Remove the FAN relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (FAN relay) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Remove the FAN relay from the engine room relay block and junction block assembly.
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1(FAN relay) - 3D-36 | Always | Below 1 Ω |
| 1(FAN relay) or 3D-36 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY) |
![]() |
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3E-1 - 3D-36 | Battery voltage is not applied between terminals 3A-27 and 3B-7 | 10 kΩ or higher |
| 3E-1 - 3D-36 | Battery voltage is applied between terminals 3A-27 and 3B-7 | Below 1 Ω |
| *1 | Instrument Panel Junction Block Assembly |
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY POWER SOURCE) |
![]() |
Disconnect the instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3E-1 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Instrument Panel Junction Block Assembly) |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND) |
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3B-7 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
Disconnect the instrument panel junction block assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3A-27 - I78-6(IG1D) | Always | Below 1 Ω |
| 3A-27 or I78-6(IG1D) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 15.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU) |
Disconnect the ECM connector.
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-5 (RFC) - A10-2 (SI) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 16.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND) |
![]() |
Disconnect the cooling fan motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z14-1 - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected (Cooling Fan Motor) |
|
| ||||
| OK | |
| 17.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - BODY GROUND) |
![]() |
Disconnect the No. 2 cooling fan motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z15-1 - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected (No. 2 Cooling Fan Motor) |
|
| ||||
| OK | ||
| ||